Add two different subnet public IPs to single NIC or two different NIC on same box


 
Thread Tools Search this Thread
Operating Systems Linux Add two different subnet public IPs to single NIC or two different NIC on same box
# 1  
Old 06-05-2018
Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins,

My ask is how can I add two different subnet IPs to same box with two different gateways?

The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected to same IP when I am connected to wifi ?
# 2  
Old 06-06-2018
Can you explain what NICs you have, what is currently configured (i.e. the output from ip a s) and what you want to add and your attempts so far. There are various options to consider, so it woud be useful to understand your needs before just setting off, otherwise this is all a bit vague.


I'm sure we can help you through.


Kind regards,
Robin
# 3  
Old 06-06-2018
Quote:
[root@master ~]# ifconfig -a
ens33: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.73.84 netmask 255.255.255.0 broadcast 192.168.73.255
inet6 fe80::20c:29ff:fe64:3347 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:64:33:47 txqueuelen 1000 (Ethernet)
RX packets 4729 bytes 5041878 (4.8 MiB)
RX errors 0 dropped 1 overruns 0 frame 0
TX packets 525 bytes 43841 (42.8 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

ens37: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.74.15 netmask 255.255.255.0 broadcast 192.168.74.255
inet6 fe80::20c:29ff:fe64:3351 prefixlen 64 scopeid 0x20<link>
ether 00:0c:29:64:33:51 txqueuelen 1000 (Ethernet)
RX packets 1000 bytes 87299 (85.2 KiB)
RX errors 0 dropped 1 overruns 0 frame 0
TX packets 9 bytes 618 (618.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
The gateway is 192.168.73.1

My ask is I need both of these IPs reachable from outside.
Or
Either any one of these IP should be reachable from outside when I connected to wifi network as well as when connected to ethernet LAN network.
# 4  
Old 06-06-2018
I think that'll need routing, even just internally. Your clients won't know that an interface has two IP's, they'll still try to use the gateway instead of going direct.
# 5  
Old 06-06-2018
tried routing.. didnt work ..may be i put wrong configs.. i followed below with some changes in IPs/subnets:

How to connect two network interfaces on the same subnet? - Red Hat Customer Portal
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Changing single path NIC to a teamed connection in same subnet

Dear all, I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths... (4 Replies)
Discussion started by: rbatte1
4 Replies

2. Solaris

Solaris 2nd nic for different subnet

posted this on the other sub-forum https://www.unix.com/unix-for-dummies-questions-and-answers/246504-solaris-11-2nd-nic-different-subnet.html apologies if linking is not appropriate Thanks for your help. (0 Replies)
Discussion started by: ad101
0 Replies

3. Solaris

Solaris 11 2nd nic for different subnet

I have a Solaris 11 machine with 2 network cables attached. The first one is the default route and is working okay. I am trying to activate the second on another subnet, but am sure missing something. The first one is on 10.30.128. and with it everything works fine, but when I try to add the... (0 Replies)
Discussion started by: ad101
0 Replies

4. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

5. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

6. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

7. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

8. Solaris

Sun box's NIC speed setting

Is there a way to check if my Sun box's network interface card is set to 10 or 100 Mbps? Thanks! (1 Reply)
Discussion started by: FredSmith
1 Replies

9. IP Networking

How to put 2 IPs on a single NIC

Hi ! I've just got a real IP number for my personal computer. Until now, the IP was masked (NAT'ed). Anyway, the problem is like this : I'm on a LAN with about 100 computers and I asked the admin to give me a real IP so that I can connect to my computer from my office. He gived that IP to me, but... (1 Reply)
Discussion started by: Sergiu-IT
1 Replies
Login or Register to Ask a Question