Visit The New, Modern Unix Linux Community


ethernet bonding


 
Thread Tools Search this Thread
Operating Systems Linux ethernet bonding
# 1  
ethernet bonding

I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.

Here's what I did:

created file /etc/modprobe.d/bonding.d and added the following to it:
Code:
alias bond0 bonding
options bonding mode=0 arp_interval=100 arp_ip_target=1.1.1.1

as for the arp_ip_target I set it to the gateway address as m not using a router. Is this correct? or I shall set the other two system IPs there?

Next, I edited the interfaces file, /etc/network/interfaces:
Code:
auto bond0
iface bond0 inet static
address 1.1.1.11
netmask 255.255.255.0
gateway 1.1.1.1
slaves eth0 eth1

bond-mode balance-rr
bond-miimon 100
bond-downdelay 200
bond-updelay 200

and finally loading bonding module into the kernel and ifconfig.
Code:
#modprobe -v bonding

if anyone has done this before, I would highly appreciate if you could tell me the exact procedure.

Your
# 2  
As far as I do remember it depends a bit how to set it up on which derivate of Linux you are using. Config files etc. may be different a bit.
You might additionally have to use the command ifenslave to attach/detach NICs to a bonding device.

I move this thread to the Linux area - don't see a relation to "Infrastructure Monitoring".
# 3  
I was under the impression that RR required switch support, but that mode 1 did not.

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

Test Your Knowledge in Computers #657
Difficulty: Easy
The last retail version of MS-DOS was MS-DOS 7.
True or False?

10 More Discussions You Might Find Interesting

1. Red Hat

Network bonding

Dear All , Very recently we have configured Network bonding in our Linux Server Redhat Linux 5.x. After configuring , we restarted the network services , the link was down after that , we could not login in to the Server. So after that , we logged in to console and tried to... (2 Replies)
Discussion started by: jegaraman
2 Replies

2. Red Hat

Network Bonding Issue

I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies

3. IP Networking

Is bond0 ready and a bonding interface? - 4G Bonding Router Problems (RPI)

HI all, First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place. I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies

4. Red Hat

BONDING with Flapping issue!

Hi team, I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1 to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The ethernet address is that of the primary interface. I have tried several different modes,... (3 Replies)
Discussion started by: leo_ultra_leo
3 Replies

5. Red Hat

Bonding a Bond with LACP

Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Discussion started by: christr
0 Replies

6. Red Hat

RHEL 5.5 NIC Bonding

I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch. The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Discussion started by: tjcooper
0 Replies

7. IP Networking

Bonding of IP tunnels

Hello. Our Company is spreaded over Germany. There are main offices an branch offices. These offices are mostly connecte via multiple sdsl. We build a IPSEC VPN Infrastructure using Aastaro Security Gateways appliances. It seemed that only one VPN Connetion between to offices could be... (0 Replies)
Discussion started by: mschwadorf
0 Replies

8. Red Hat

IP Bonding

Hi, What is IP bonding in Linux. What are its advantages How to create a IP bonding in redhat Linux. (1 Reply)
Discussion started by: chetansingh23
1 Replies

9. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies

10. IP Networking

Bonding Internet Connections

I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster... (0 Replies)
Discussion started by: harley313
0 Replies

Featured Tech Videos