Can not get wireless to register in linux mint?


 
Thread Tools Search this Thread
Operating Systems Linux Can not get wireless to register in linux mint?
# 1  
Old 06-07-2011
Error Can not get wireless to register in linux mint?

I just installed linux mint 11 yesterday. I cannot get the wireless to register, it says that firmware is missing but I can not figure out how to make it work. I am still a newbie and would appreciate any help possible. Thank you.
# 2  
Old 06-07-2011
what does lspci show you? what do you see in dmesg?
This User Gave Thanks to Corona688 For This Post:
# 3  
Old 06-07-2011
Question dmesg coped and pasted, dont know what ispci is. sorry so new

I dont know what ispci does or how to do it but i copyed and pasted the dmesg

dmsg-

Code:
[    0.770151] ACPI: Power Button [PWRF]
[    0.770473] ACPI: acpi_idle registered with cpuidle
[    0.770528] Marking TSC unstable due to TSC halts in idle
[    0.806464] ACPI: Invalid active0 threshold
[    0.809886] thermal LNXTHERM:00: registered as thermal_zone0
[    0.809894] ACPI: Thermal Zone [THRM] (47 C)
[    0.809960] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[    0.810153] ERST: Table is not found!
[    0.810333] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.813521] ACPI: PCI Interrupt Link [LMCI] enabled at IRQ 22
[    0.813554] serial 0000:00:06.1: PCI INT B -> Link[LMCI] -> GSI 22 (level, low) -> IRQ 22
[    0.813568] serial 0000:00:06.1: PCI INT B disabled
[    0.813925] Linux agpgart interface v0.103
[    0.813987] agpgart-amd64 0000:00:00.0: AGP bridge [10de/00d1]
[    0.814001] agpgart-amd64 0000:00:00.0: aperture size 4096 MB is not right, using settings from NB
[    0.814013] agpgart-amd64 0000:00:00.0: setting up Nforce3 AGP
[    0.824273] isapnp: Scanning for PnP cards...
[    0.929015] agpgart-amd64 0000:00:00.0: AGP aperture is 128M @ 0xe8000000
[    0.932268] brd: module loaded
[    0.933806] loop: module loaded
[    0.934048] i2c-core: driver [adp5520] using legacy suspend method
[    0.934054] i2c-core: driver [adp5520] using legacy resume method
[    0.934453] pata_acpi 0000:00:08.0: setting latency timer to 64
[    0.935525] Fixed MDIO Bus: probed
[    0.935640] PPP generic driver version 2.4.2
[    0.935741] tun: Universal TUN/TAP device driver, 1.6
[    0.935746] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.935970] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.940387] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
[    0.940420] ehci_hcd 0000:00:02.2: PCI INT C -> Link[LUS2] -> GSI 21 (level, low) -> IRQ 21
[    0.940451] ehci_hcd 0000:00:02.2: setting latency timer to 64
[    0.940459] ehci_hcd 0000:00:02.2: EHCI Host Controller
[    0.940577] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
[    0.940644] ehci_hcd 0000:00:02.2: cache line size of 64 is not supported
[    0.940680] ehci_hcd 0000:00:02.2: irq 21, io mem 0xe0004000
[    0.991599] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00
[    0.991913] hub 1-0:1.0: USB hub found
[    0.991925] hub 1-0:1.0: 6 ports detected
[    1.080526] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.080919] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20
[    1.080956] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 20 (level, low) -> IRQ 20
[    1.080990] ohci_hcd 0000:00:02.0: setting latency timer to 64
[    1.080998] ohci_hcd 0000:00:02.0: OHCI Host Controller
[    1.081137] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[    1.081204] ohci_hcd 0000:00:02.0: irq 20, io mem 0xe0000000
[    1.138638] hub 2-0:1.0: USB hub found
[    1.138653] hub 2-0:1.0: 3 ports detected
[    1.139125] ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 22
[    1.139137] ohci_hcd 0000:00:02.1: PCI INT B -> Link[LUS1] -> GSI 22 (level, low) -> IRQ 22
[    1.139164] ohci_hcd 0000:00:02.1: setting latency timer to 64
[    1.139172] ohci_hcd 0000:00:02.1: OHCI Host Controller
[    1.139283] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
[    1.139334] ohci_hcd 0000:00:02.1: irq 22, io mem 0xe0001000
[    1.194345] hub 3-0:1.0: USB hub found
[    1.194357] hub 3-0:1.0: 3 ports detected
[    1.194526] uhci_hcd: USB Universal Host Controller Interface driver
[    1.194748] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.203885] i8042: Detected active multiplexing controller, rev 1.1
[    1.223096] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.223119] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.228073] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.228154] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.228231] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.228583] mousedev: PS/2 mouse device common for all mice
[    1.229016] rtc_cmos 00:06: RTC can wake from S4
[    1.229128] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[    1.229163] rtc0: alarms up to one year, y3k, 114 bytes nvram
[    1.229401] device-mapper: uevent: version 1.0.3
[    1.229607] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised: dm-devel@redhat.com
[    1.231658] device-mapper: multipath: version 1.2.0 loaded
[    1.231665] device-mapper: multipath round-robin: version 1.0.0 loaded
[    1.231876] EISA: Probing bus 0 at eisa.0
[    1.231883] EISA: Cannot allocate resource for mainboard
[    1.231890] Cannot allocate resource for EISA slot 1
[    1.231897] Cannot allocate resource for EISA slot 2
[    1.231903] Cannot allocate resource for EISA slot 3
[    1.231910] Cannot allocate resource for EISA slot 4
[    1.231916] Cannot allocate resource for EISA slot 5
[    1.231922] Cannot allocate resource for EISA slot 6
[    1.231929] Cannot allocate resource for EISA slot 7
[    1.231935] Cannot allocate resource for EISA slot 8
[    1.231941] EISA: Detected 0 cards.
[    1.235140] cpuidle: using governor ladder
[    1.235257] cpuidle: using governor menu
[    1.235927] TCP cubic registered
[    1.236298] NET: Registered protocol family 10
[    1.237737] NET: Registered protocol family 17
[    1.237782] Registering the dns_resolver key type
[    1.237826] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ (1 cpu cores) (version 2.20.00)
[    1.338793] isapnp: No Plug & Play device found
[    1.338844] powernow-k8:    0 : fid 0xa (1800 MHz), vid 0x2
[    1.338851] powernow-k8:    1 : fid 0x8 (1600 MHz), vid 0x6
[    1.338858] powernow-k8:    2 : fid 0x0 (800 MHz), vid 0x12
[    1.384438] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    1.390865] Using IPI No-Shortcut mode
[    1.391000] PM: Hibernation image not present or could not be loaded.
[    1.391015] registered taskstats version 1
[    1.391235]   Magic number: 15:772:897
[    1.392631] rtc_cmos 00:06: setting system clock to 2011-06-07 18:51:11 UTC (1307472671)
[    1.392635] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.392637] EDD information not available.
[    1.452184] ACPI: Battery Slot [BAT1] (battery present)
[    1.652322] Freeing initrd memory: 12788k freed
[    1.667528] Freeing unused kernel memory: 700k freed
[    1.668353] Write protecting the kernel text: 5192k
[    1.668396] Write protecting the kernel read-only data: 2148k
[    1.694014] <30>udev[61]: starting version 167
[    1.781199] Btrfs loaded
[    1.805375] xor: automatically using best checksumming function: pIII_sse
[    1.824011]    pIII_sse  :  5423.000 MB/sec
[    1.824014] xor: using function: pIII_sse (5423.000 MB/sec)
[    1.841438] device-mapper: dm-raid45: initialized v0.2594b
[    1.918379] pata_amd 0000:00:08.0: version 0.4.1
[    1.918452] pata_amd 0000:00:08.0: setting latency timer to 64
[    2.000924] scsi0 : pata_amd
[    2.005574] scsi1 : pata_amd
[    2.006140] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2080 irq 14
[    2.006144] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2088 irq 15
[    2.018467] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[    2.018492] 8139cp 0000:02:01.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[    2.045359] ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 17
[    2.045384] b43-pci-bridge 0000:02:02.0: PCI INT A -> Link[LNK3] -> GSI 17 (level, low) -> IRQ 17
[    2.045424] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x04, vendor 0x4243)
[    2.045430] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x05, vendor 0x4243)
[    2.045436] ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x02, vendor 0x4243)
[    2.045441] ssb: Core 3 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
[    2.045447] ssb: Core 4 found: PCI (cc 0x804, rev 0x09, vendor 0x4243)
[    2.049322] ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
[    2.168382] ata1.00: ATA-6: TOSHIBA MK8025GAS, KA024A, max UDMA/100
[    2.168387] ata1.00: 156301488 sectors, multi 16: LBA 
[    2.168397] ata1: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[    2.176300] ata1.00: configured for UDMA/100
[    2.176443] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK8025GA KA02 PQ: 0 ANSI: 5
[    2.176646] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.176845] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[    2.176901] sd 0:0:0:0: [sda] Write Protect is off
[    2.176905] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.176931] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.266024]  sda: sda1 sda2 < sda5 >
[    2.266411] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.340365] ata2.00: ATAPI: SD-R2512, 1A04, max MWDMA2
[    2.340373] ata2: nv_mode_filter: 0x39f&0x739f->0x39f, BIOS=0x0 (0xc6000000) ACPI=0x39f (120:600:0x12)
[    2.356298] ata2.00: configured for MWDMA2
[    2.362298] scsi 1:0:0:0: CD-ROM            TOSHIBA  DVD-ROM SD-R2512 1A04 PQ: 0 ANSI: 5
[    2.366558] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    2.366562] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.366668] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.366741] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    2.373676] firewire_ohci 0000:02:00.0: PCI INT A -> Link[LNK1] -> GSI 19 (level, low) -> IRQ 19
[    2.380525] 8139too: 8139too Fast Ethernet driver 0.9.28
[    2.428110] firewire_ohci: Added fw-ohci device 0000:02:00.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2
[    2.428203] 8139too 0000:02:01.0: PCI INT A -> Link[LNK2] -> GSI 18 (level, low) -> IRQ 18
[    2.429612] 8139too 0000:02:01.0: eth0: RealTek RTL8139 at 0x7000, 00:0f:b0:0c:f8:80, IRQ 18
[    2.928342] firewire_core: created device fw0: GUID 493f0200493f0200, S400
[    2.941130] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[    2.941136] EXT4-fs (sda1): write access will be enabled during recovery
[    3.010517] EXT4-fs (sda1): recovery complete
[    3.011110] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[    5.040054] floppy0: no floppy controllers found
[   15.691739] <30>udev[295]: starting version 167
[   15.706741] Adding 784380k swap on /dev/sda5.  Priority:-1 extents:1 across:784380k 
[   15.725654] lp: driver loaded but no devices found
[   15.956528] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   16.424566] i2c i2c-0: nForce2 SMBus adapter at 0x2040
[   16.424633] i2c i2c-1: nForce2 SMBus adapter at 0x2000
[   16.426017] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[   16.558798] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:18/LNXVIDEO:00/input/input4
[   16.558905] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   16.559769] parport_pc 00:0b: reported by Plug and Play ACPI
[   16.559795] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[   16.564052] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   16.758201] lp0: using parport0 (interrupt-driven).
[   17.202048] yenta_cardbus 0000:02:04.0: CardBus bridge found [103c:006d]
[   17.202068] yenta_cardbus 0000:02:04.0: CardBus bridge to [bus 03-06]
[   17.202073] yenta_cardbus 0000:02:04.0:   bridge window [io  0x3000-0x30ff]
[   17.202078] yenta_cardbus 0000:02:04.0:   bridge window [io  0x3400-0x34ff]
[   17.202084] yenta_cardbus 0000:02:04.0:   bridge window [mem 0x30000000-0x33ffffff pref]
[   17.202089] yenta_cardbus 0000:02:04.0:   bridge window [mem 0xe0400000-0xe07fffff]
[   17.202095] yenta_cardbus 0000:02:04.0: Enabling burst memory read transactions
[   17.202100] yenta_cardbus 0000:02:04.0: Using CSCINT to route CSC interrupts to PCI
[   17.202103] yenta_cardbus 0000:02:04.0: Routing CardBus interrupts to PCI
[   17.202108] yenta_cardbus 0000:02:04.0: TI: mfunc 0x01111d22, devctl 0x64
[   17.205663] input: PS/2 Mouse as /devices/platform/i8042/serio4/input/input5
[   17.224633] ppdev: user-space parallel port driver
[   17.227079] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio4/input/input6
[   17.319640] cfg80211: Calling CRDA to update world regulatory domain
[   17.340574] [drm] Initialized drm 1.1.0 20060810
[   17.359138] cfg80211: World regulatory domain updated:
[   17.359143] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   17.359148] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   17.359151] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   17.359155] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   17.359158] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   17.359162] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   17.432600] yenta_cardbus 0000:02:04.0: ISA IRQ mask 0x0c38, PCI irq 19
[   17.432606] yenta_cardbus 0000:02:04.0: Socket status: 30000086
[   17.432612] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #02 to #06
[   17.432623] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge window: [io  0x3000-0x7fff]
[   17.432628] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3000-0x7fff: excluding 0x3000-0x30ff 0x3400-0x34ff 0x3800-0x38ff 0x3c00-0x3cff 0x7000-0x70ff 0x7400-0x743f
[   17.560983] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge window: [mem 0xe0100000-0xe17fffff]
[   17.560990] pcmcia_socket pcmcia_socket0: cs: memory probe 0xe0100000-0xe17fffff: excluding 0xe0100000-0xe026ffff 0xe03e0000-0xe082ffff
[   17.561006] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge window: [mem 0x30000000-0x37ffffff pref]
[   17.561010] pcmcia_socket pcmcia_socket0: cs: memory probe 0x30000000-0x37ffffff: excluding 0x30000000-0x37ffffff
[   17.572172] yenta_cardbus 0000:02:04.1: CardBus bridge found [103c:006d]
[   17.572192] yenta_cardbus 0000:02:04.1: Using CSCINT to route CSC interrupts to PCI
[   17.572195] yenta_cardbus 0000:02:04.1: Routing CardBus interrupts to PCI
[   17.572201] yenta_cardbus 0000:02:04.1: TI: mfunc 0x01111d22, devctl 0x64
[   17.605352] b43-phy0: Broadcom 4306 WLAN found (core revision 5)
[   17.639245] nouveau 0000:01:00.0: power state changed by ACPI to D0
[   17.639253] nouveau 0000:01:00.0: power state changed by ACPI to D0
[   17.639441] ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 16
[   17.639461] nouveau 0000:01:00.0: PCI INT A -> Link[LNK5] -> GSI 16 (level, low) -> IRQ 16
[   17.648940] [drm] nouveau 0000:01:00.0: Detected an NV10 generation card (0x017900a5)
[   17.649151] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PRAMIN
[   17.715601] [drm] nouveau 0000:01:00.0: ... appears to be valid
[   17.715847] [drm] nouveau 0000:01:00.0: BMP BIOS found
[   17.715850] [drm] nouveau 0000:01:00.0: BMP version 5.41
[   17.715854] [drm] nouveau 0000:01:00.0: Bios version 04.17.20.49
[   17.715858] [drm] nouveau 0000:01:00.0: Found Display Configuration Block version 2.2
[   17.715863] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01000100 000088b8
[   17.715866] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 03010223 00000004
[   17.715870] [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 020203f1 00000003
[   17.716097] [drm] nouveau 0000:01:00.0: Loading NV17 power sequencing microcode
[   17.716103] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xF302
[   17.716150] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xF828
[   17.716166] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xF42A
[   17.717703] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[   17.717708] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717711] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[   17.717715] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717718] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[   17.717722] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717725] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[   17.717728] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717731] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[   17.717735] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717738] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[   17.717742] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717745] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[   17.717748] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717751] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[   17.717755] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717758] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[   17.717762] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717765] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[   17.717768] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717771] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[   17.717775] cfg80211: 2402000 KHz - 2472000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717778] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[   17.717782] cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717785] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[   17.717788] cfg80211: 2457000 KHz - 2482000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.717791] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[   17.717795] cfg80211: 2474000 KHz - 2494000 KHz @  KHz), (300 mBi, 2000 mBm)
[   17.721968] ACPI: PCI Interrupt Link [LACI] enabled at IRQ 21
[   17.721978] Intel ICH 0000:00:06.0: PCI INT A -> Link[LACI] -> GSI 21 (level, low) -> IRQ 21
[   17.722011] Intel ICH 0000:00:06.0: setting latency timer to 64
[   17.729842] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   17.730622] Registered led device: b43-phy0::tx
[   17.730649] Registered led device: b43-phy0::rx
[   17.730676] Registered led device: b43-phy0::radio
[   17.730699] Broadcom 43xx driver loaded [ Features: PNL, Firmware-ID: FW13 ]
[   17.736125] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xFB3C
[   17.736138] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xFB69
[   17.736145] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 5 at offset 0xF608
[   17.788569] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 6 at offset 0xF7C3
[   17.844588] yenta_cardbus 0000:02:04.1: ISA IRQ mask 0x0c38, PCI irq 18
[   17.844595] yenta_cardbus 0000:02:04.1: Socket status: 30000006
[   17.844600] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #06 to #0a
[   17.844610] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge window: [io  0x3000-0x7fff]
[   17.844616] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3000-0x7fff: excluding 0x3000-0x30ff 0x3400-0x34ff 0x3800-0x38ff 0x3c00-0x3cff 0x7000-0x70ff 0x7400-0x743f
[   17.873801] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge window: [mem 0xe0100000-0xe17fffff]
[   17.873806] pcmcia_socket pcmcia_socket1: cs: memory probe 0xe0100000-0xe17fffff: excluding 0xe0100000-0xe026ffff 0xe03e0000-0xe082ffff 0xe0b10000-0xe10cffff
[   17.873823] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge window: [mem 0x30000000-0x37ffffff pref]
[   17.873827] pcmcia_socket pcmcia_socket1: cs: memory probe 0x30000000-0x37ffffff: excluding 0x30000000-0x37ffffff
[   17.879063] [drm] nouveau 0000:01:00.0: 0 available performance level(s)
[   17.879076] [drm] nouveau 0000:01:00.0: c: memory 405MHz core 189MHz
[   17.883870] [TTM] Zone  kernel: Available graphics memory: 382952 kiB.
[   17.883875] [TTM] Initializing pool allocator.
[   17.883891] [drm] nouveau 0000:01:00.0: Detected 64MiB VRAM
[   17.884549] agpgart-amd64 0000:00:00.0: AGP 2.0 bridge
[   17.884573] agpgart-amd64 0000:00:00.0: putting AGP V2 device into 4x mode
[   17.884626] nouveau 0000:01:00.0: putting AGP V2 device into 4x mode
[   17.884631] [drm] nouveau 0000:01:00.0: 128 MiB GART (aperture)
[   17.884677] [drm] nouveau 0000:01:00.0: Saving VGA fonts
[   17.959059] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found
[   17.959065] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found
[   17.959069] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.
[   17.980075] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   17.980081] [drm] No driver support for vblank timestamp query.
[   17.981543] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
[   17.981551] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on lvds encoder (output 1)
[   17.981557] [drm] nouveau 0000:01:00.0: Calling LVDS script 1:
[   17.981563] [drm] nouveau 0000:01:00.0: Calling LVDS script 6:
[   17.981567] [drm] nouveau 0000:01:00.0: 0xE457: Parsing digital output script table
[   18.045556] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af: excluding nothing: probe failed.
[   18.045640] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: excluding nothing: probe failed.
[   18.045706] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: excluding nothing: probe failed.
[   18.045768] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: excluding nothing: probe failed.
[   18.045834] pcmcia_socket pcmcia_socket1: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xfffff
[   18.045890] pcmcia_socket pcmcia_socket1: cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
[   18.045947] pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
[   18.046005] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: excluding nothing: probe failed.
[   18.047205] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding nothing: probe failed.
[   18.047284] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding nothing: probe failed.
[   18.047344] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: excluding nothing: probe failed.
[   18.047401] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: excluding nothing: probe failed.
[   18.047460] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xfffff
[   18.047514] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
[   18.047566] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
[   18.047620] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: excluding nothing: probe failed.
[   18.664045] intel8x0_measure_ac97_clock: measured 54772 usecs (2656 samples)
[   18.664051] intel8x0: clocking to 48000
[   18.784043] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV encoder (output 2)
[   19.008563] [drm] nouveau 0000:01:00.0: allocated 1280x800 fb: 0x49000, bo e69c5400
[   19.011095] Console: switching to colour frame buffer device 160x50
[   19.011134] fb0: nouveaufb frame buffer device
[   19.011136] drm: registered panic notifier
[   19.011147] [drm] Initialized nouveau 0.0.16 20090420 for 0000:01:00.0 on minor 0
[   19.584061] floppy0: no floppy controllers found
[   20.446222] [drm] nouveau 0000:01:00.0: Calling LVDS script 2:
[   20.446229] [drm] nouveau 0000:01:00.0: 0xE4BA: Parsing digital output script table
[   20.464071] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on lvds encoder (output 1)
[   20.464075] [drm] nouveau 0000:01:00.0: Calling LVDS script 5:
[   20.464078] [drm] nouveau 0000:01:00.0: 0xE3E4: Parsing digital output script table
[   20.464096] [drm] nouveau 0000:01:00.0: Output LVDS-1 is running on CRTC 1 using output A
[   21.466858] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[   25.239024] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[   27.176030] eth0: no IPv6 routers present
[ 1329.359224] eth0: link down
[ 1331.896508] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=600
[ 1350.816068] usb 1-3: new high speed USB device using ehci_hcd and address 2
[ 1351.222254] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 1351.222265] ata1.00: BMDMA stat 0x24
[ 1351.222275] ata1.00: failed command: READ DMA
[ 1351.222294] ata1.00: cmd c8/00:f8:18:23:16/00:00:00:00:00/e2 tag 0 dma 126976 in
[ 1351.222298]          res 51/84:01:0f:24:16/00:00:00:00:00/e2 Emask 0x10 (ATA bus error)
[ 1351.222307] ata1.00: status: { DRDY ERR }
[ 1351.222313] ata1.00: error: { ICRC ABRT }
[ 1351.222347] ata1: soft resetting link
[ 1351.384453] ata1: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 1351.392377] ata1.00: configured for UDMA/100
[ 1351.392402] ata1: EH complete
[ 1351.550710] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 1351.550721] ata1.00: BMDMA stat 0x24
[ 1351.550731] ata1.00: failed command: READ DMA
[ 1351.550750] ata1.00: cmd c8/00:f8:18:23:16/00:00:00:00:00/e2 tag 0 dma 126976 in
[ 1351.550754]          res 51/84:01:0f:24:16/00:00:00:00:00/e2 Emask 0x10 (ATA bus error)
[ 1351.550762] ata1.00: status: { DRDY ERR }
[ 1351.550768] ata1.00: error: { ICRC ABRT }
[ 1351.550802] ata1: soft resetting link
[ 1351.712447] ata1: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 1351.720343] ata1.00: configured for UDMA/100
[ 1351.720372] ata1: EH complete
[ 1351.921966] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 1351.921977] ata1.00: BMDMA stat 0x24
[ 1351.921987] ata1.00: failed command: READ DMA
[ 1351.922006] ata1.00: cmd c8/00:58:38:37:c4/00:00:00:00:00/e3 tag 0 dma 45056 in
[ 1351.922010]          res 51/84:01:8f:37:c4/00:00:00:00:00/e3 Emask 0x10 (ATA bus error)
[ 1351.922019] ata1.00: status: { DRDY ERR }
[ 1351.922025] ata1.00: error: { ICRC ABRT }
[ 1351.922059] ata1: soft resetting link
[ 1352.084494] ata1: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 1352.092349] ata1.00: configured for UDMA/100
[ 1352.092371] ata1: EH complete
[ 1352.393163] ata1.00: limiting speed to UDMA/66:PIO4
[ 1352.393176] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
[ 1352.393185] ata1.00: BMDMA stat 0x24
[ 1352.393193] ata1.00: failed command: READ DMA
[ 1352.393211] ata1.00: cmd c8/00:08:c8:59:c5/00:00:00:00:00/e3 tag 0 dma 4096 in
[ 1352.393215]          res 51/84:01:cf:59:c5/00:00:00:00:00/e3 Emask 0x10 (ATA bus error)
[ 1352.393223] ata1.00: status: { DRDY ERR }
[ 1352.393229] ata1.00: error: { ICRC ABRT }
[ 1352.393264] ata1: soft resetting link
[ 1352.556470] ata1: nv_mode_filter: 0x1f39f&0x3f39f->0x1f39f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 1352.564397] ata1.00: configured for UDMA/66
[ 1352.564418] ata1: EH complete
[ 1352.988852] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04A9 pid 0x10C4
[ 1352.990379] usbcore: registered new interface driver usblp
[ 1354.154672] usb 1-3: usbfs: interface 0 claimed by usblp while 'usb' sets config #1
[ 1555.224110] usb 1-3: USB disconnect, address 2
[ 1555.224357] usblp0: removed
[ 1635.675815] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0
[ 2146.772589] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1


Last edited by pludi; 06-07-2011 at 06:42 PM..
# 4  
Old 06-07-2011
lspci lists pci things. You do it by typing in 'lspci' as root. If you don't have it, you should install it because it's really necessary. I see a 'b43' in there, which may mean you have a broadcom chip, which may need proprietary drivers.
This User Gave Thanks to Corona688 For This Post:
# 5  
Old 06-07-2011
Still confused

How do you install ispci? i tried sudo-apt get install ispci but it did not work. i also looked for it the package manager... Sorry you gotta use total lamans terms with me. thank you tons though.... Im still totally lost....SmilieSmilie
# 6  
Old 06-07-2011
There's not a secret name for lspci as far as I know. Google finds nothing about installing it so I think it comes installed. Are you running lspci as root, or just sudoing it or what? When I mean as root I mean from a root console, not with sudo, because it may not be in your PATH. What happens when you do 'which lspci'?
# 7  
Old 06-07-2011
Quote:
Originally Posted by breebutner
I dont know what ispci does or how to do it
Quote:
Originally Posted by breebutner
How do you install ispci? i tried sudo-apt get install ispci but it did not work.
It's lspci not ispci.

Regards,
Alister
This User Gave Thanks to alister For This Post:
Login or Register to Ask a Question

Previous Thread | Next Thread

3 More Discussions You Might Find Interesting

1. Debian

Linux Mint 16

I use linux mint 16 and I'm new to live ux. what should I know? (4 Replies)
Discussion started by: Cryptek
4 Replies

2. Linux

Linux Mint Wireless Help (Gateway 600)

Hi, I have successfully installed the latest Linux Mint for the very first time on an old (2001) Gateway 600 laptop. I still have my old Windows XP on this too. I cannot figure out how to get the wireless connection to work (to connect to my home router). I have tried installing my only... (5 Replies)
Discussion started by: ssid61
5 Replies

3. Linux

Wireless issues in Linux Mint.

I am running Linux Mint Gloria on my PC. I have ADSL broadband connection which require login and pswd connection to connect. I have SmartAX MT841 modem which has wireless card free with it. I also have recently purchased DELL inspiron 1545 machine which have Vista preinstalled in it. Now I want to... (0 Replies)
Discussion started by: budtuxy
0 Replies
Login or Register to Ask a Question

Featured Tech Videos