10 More Discussions You Might Find Interesting
1. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
2. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
3. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
4. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
5. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
6. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
7. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
8. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
9. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
10. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
MV(1) FSF MV(1)
NAME
mv - move (rename) files
SYNOPSIS
mv [OPTION]... SOURCE DEST
mv [OPTION]... SOURCE... DIRECTORY
mv [OPTION]... --target-directory=DIRECTORY SOURCE...
DESCRIPTION
Rename SOURCE to DEST, or move SOURCE(s) to DIRECTORY.
Mandatory arguments to long options are mandatory for short options too.
--backup[=CONTROL]
make a backup of each existing destination file
-b like --backup but does not accept an argument
-f, --force
do not prompt before overwriting equivalent to --reply=yes
-i, --interactive
prompt before overwrite equivalent to --reply=query
--reply={yes,no,query}
specify how to handle the prompt about an existing destination file
--strip-trailing-slashes remove any trailing slashes from each SOURCE
argument
-S, --suffix=SUFFIX
override the usual backup suffix
--target-directory=DIRECTORY
move all SOURCE arguments into DIRECTORY
-u, --update
move only when the SOURCE file is newer than the destination file or when the destination file is missing
-v, --verbose
explain what is being done
--help display this help and exit
--version
output version information and exit
The backup suffix is `~', unless set with --suffix or SIMPLE_BACKUP_SUFFIX. The version control method may be selected via the --backup
option or through the VERSION_CONTROL environment variable. Here are the values:
none, off
never make backups (even if --backup is given)
numbered, t
make numbered backups
existing, nil
numbered if numbered backups exist, simple otherwise
simple, never
always make simple backups
AUTHOR
Written by Mike Parker, David MacKenzie, and Jim Meyering.
REPORTING BUGS
Report bugs to <bug-coreutils@gnu.org>.
COPYRIGHT
Copyright (C) 2002 Free Software Foundation, Inc.
This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU-
LAR PURPOSE.
SEE ALSO
The full documentation for mv is maintained as a Texinfo manual. If the info and mv programs are properly installed at your site, the com-
mand
info mv
should give you access to the complete manual.
mv (coreutils) 4.5.3 February 2003 MV(1)