Is my data lost? Installed Linux, no longer can I access my hard drives.
Here's the story -
I installed Linux on my Y drive, and all went well until I tried to boot into XP again. I can't access or install an operating system to my other three hard drives, C, X, and Z.
I think that during the install my hard drives were changed to something other then NTFS, but Linux won't access them either.
When I use my Windows XP or Windows 7 disc, it says the drive has 0mb free, and it can't install until I delete the partition, then reformat. I don't want to do this obviously, because I don't want to format all of my data.
When I go to Places > My Computer it lists my CD drive, Filesystem, and the Y drive. It doesn't show my other three hard drives.
Under Palimpsest Disk Utility I can see my other three drives, but I can't access the data on them yet.
You don't say which Linux distro you installed or whether it was a "Live" version, it is possible you have created a system wide LVM.
If you have gparted installed see what it says about your disk partitions. If it's not installed try downloading the systemrescue cd from Main Page - SystemRescueCd (always useful to have) and see what gparted and the other tools have to say.
Since the lost of the rtc all the settings became default. Does anyone remember what needs to be reset to discover both Hard drives? It sees the DVD and the scsi disk (intscsib.0) in 0/1/1/1.0 (disk 1 slot) but not 0/1/1/0.1 (intscsia.1)(disk 0 slot).
Right now, from the service menu, scsi shows... (3 Replies)
Ok so i thought i was smart but i can tell I need some help. I am playing around with understanding lvm and adding disks to a linux box. I added a disk and then ran what i thought were commands to add this disk to the box but I think I messed up and would like some help. My question is did i... (5 Replies)
Hi,
I have two SCSI Hard Drives in a Sun Solaris 8 server as shown below. I would like to access Disk1 and look at its contents, directory structure and files. How do I change my default directory from Disk 0 to Disk 1 and vice versa?
Thank you. (5 Replies)
Hello everyone. I have a question which I may know the answer to, I'm just looking for a confirmation. When it comes to the MBR of a hard drive, i've read in multiple sources that it's always located in the first sector of the hard drive. Is the MBR there from the factory? When I buy a new blank... (3 Replies)
I have a T2000 Sun-Fire server. I have 2 sets of drives in a raid 1. Lets call them Set A and Set B. I had Set A installed and working. I needed a new install so I so build up Set B. After some time I wanted to put Set A back in the server. Now the system will not boot off of Set A. I tried to boot... (7 Replies)
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Folks;
I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version.
Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
I am using an Acer Aspire 4720Z with two partitions C and D. Windows is installed on C and I decided to install Red Hat Linux 9 in partition D. The two partitions are in NTFS file system. During my installation of the the Linux, a prompt was displayed on screen with the message: "No hard drives... (2 Replies)
Will some one tell me what this means.
"warning: ida 0 <slot 6> : command timed out on dev 1/42 blk 4824290 logical unit=0 blocks=5512102, size 2, cmd=0x20."
I'm running SCO 505 on a proliant 1600r.
Thnank you in advance. (3 Replies)