Login or Register to Ask a Question and Join Our Community


IP Networking

Network Card with SGI

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Special Forums IP Networking Network Card with SGI
# 1  
Old 10-10-2002
Network Card with SGI
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >

But now the link network just refuses to work . I know the jack is working because i tried it on the Mac alongside it . But it dosent work with IRIX . I tried rebooting but to no avail . So i put it on diagnosis mode to see if there was a hardware failure . Didnt show anything unusual . So i booted it again . The network started working . Just out of curiosity I pulled out the Ethernet cable and fixed it again and there, it went down with it.

Now is it that i cant disconnect the cable when the machine is on when it comes to SGI. and if it is intrinsic how can i make it to network again.

My hunch is the n/w card is nearing its end but still i do not want to jump to conclusions..

Thanx
DP
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Ubuntu

Error on network card

Hi Please can you help me to understand what could be wrong based on what I have captured in the logs: I have run cat /var/log/syslog | grep -i warn, and I got the following output NetworkManager: <warn> Activation (eth3) failed. Dec 23 10:58:25 cmoveldb02 NetworkManager: <warn> (eth3): DHCPv4... (2 Replies)
Discussion started by: fretagi
2 Replies

2. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies

3. Solaris

Network Card Name details

Hi All, Can somebody explain that whats the meaning of different interfaces naming scheme, Like ' hme, qfe, e1000g0, ce, eri, bge' ? This is such a basic question which i always overlooked :( Thanks ! (6 Replies)
Discussion started by: Solarister
6 Replies

4. Solaris

How to identifying the network card ?

Hi Experts, Can we use some command from unix to find the available network interface? I did tried Its listing following, however how can I decide the which vender card is attached e.g. if its hme , bge or some thing else Thanks (7 Replies)
Discussion started by: kumarmani
7 Replies

5. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies

6. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies

7. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies

8. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

9. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies

10. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies
Login or Register to Ask a Question

LEARN ABOUT X11R4

network_namespaces

NETWORK_NAMESPACES(7)					     Linux Programmer's Manual					     NETWORK_NAMESPACES(7)

NAME

       network_namespaces - overview of Linux network namespaces

DESCRIPTION

       Network namespaces provide isolation of the system resources associated with networking: network devices, IPv4 and IPv6 protocol stacks, IP
       routing tables, firewall rules, the /proc/net directory (which is a symbolic link to /proc/PID/net), the /sys/class/net directory,  various
       files under /proc/sys/net, port numbers (sockets), and so on.

       A physical network device can live in exactly one network namespace.  When a network namespace is freed (i.e., when the last process in the
       namespace terminates), its physical network devices are moved back to the initial network namespace (not to the parent of the process).

       A virtual network (veth(4)) device pair provides a pipe-like abstraction that can be used to create tunnels between network namespaces, and
       can  be	used to create a bridge to a physical network device in another namespace.  When a namespace is freed, the veth(4) devices that it
       contains are destroyed.

       Use of network namespaces requires a kernel that is configured with the CONFIG_NET_NS option.

SEE ALSO

       nsenter(1), unshare(1), clone(2), veth(4), proc(5),  sysfs(5),  namespaces(7),  user_namespaces(7),  brctl(8),  ip(8),  ip-address(8),  ip-
       link(8), ip-netns(8), iptables(8), ovs-vsctl(8)

COLOPHON

       This  page is part of release 4.15 of the Linux man-pages project.  A description of the project, information about reporting bugs, and the
       latest version of this page, can be found at https://www.kernel.org/doc/man-pages/.

Linux								    2018-02-02						     NETWORK_NAMESPACES(7)