10 More Discussions You Might Find Interesting
1. Red Hat
Hi guys,
I really need your help with this.
My network interface eth0 is up but not running. I checked udev rules and ifcfg-eth0 files to make sure the mac address are the same.
It just would not come up. Please please I will really appreciate the help here.
Thank you in advance. (3 Replies)
Discussion started by: cjashu
3 Replies
2. IP Networking
Hi all,
I am running a CentOS 6.4 box as an IDS and I need to configure one interface as the management interface which will require a firewall. However other ports (in promisc mode without IP) will have to be configured such that IPtables allows all traffic.
I need to achieve this by editing... (4 Replies)
Discussion started by: landossa
4 Replies
3. Red Hat
Hello, I'm using dell inspiron 14R laptop and I installed Redhat enterprise 6.2 on this. After successfully installation i did not found any network interface on this.
when i'm trying to load/add qeth driver . The driver is not found showing this message.
Bash: lsmod | grep qeth
Bash:... (4 Replies)
Discussion started by: dearsumon
4 Replies
4. Red Hat
Hi,
I have noticed some performance issues on my RHEL5 server but the memory and CPU utilization on the box is fine.
I have a 1G full duplexed eth0 card and I am suspicious that this may be causing the problem. My eth0 settings are as follows:
Settings for eth0:
Supported ports: ... (12 Replies)
Discussion started by: Duffs22
12 Replies
5. Red Hat
Hi,
I have just installed RHEL 5.4 on a BL430c-class server and I am attempting to connect to the network only when I try and start eth0, I get the following error?
"Bringing up Interface eth0: hp device eth0 does not seem to be present, delaying initialization."
I am using a HP... (18 Replies)
Discussion started by: Duffs22
18 Replies
6. UNIX for Dummies Questions & Answers
Hi Guys,
is there a way to send traffic coming from the source iface (eth0, eth1)? i need to test traffic that will come from both eth0 and eth1 from a Linux box.
Thanks,
Martin (0 Replies)
Discussion started by: mdap
0 Replies
7. UNIX for Dummies Questions & Answers
Hi,
Just installed Centos 5.1 on HP DL360, on this system I have to close to ten nic's. How can I find which one is eth0? When I do " ifconfig -a" I see all of them, but I can't tell which is eth0?
Please advice. (2 Replies)
Discussion started by: samnyc
2 Replies
8. Ubuntu
Greetings,
I have installed a Ubuntu server and attempting put a static IP address on interface ETH0. I edited the /etc/network/interfaces with the following:
auto eth0
iface eth0 inet static
address 192.168.203.270
gateway 192.168.203.1
netwask 255.255.255.0
network 192.168.0.0... (2 Replies)
Discussion started by: jroberson
2 Replies
9. Red Hat
when i finish installed rhel 4.4 to my hp dl585 box, ifcfg-eth0 and ifcfg-eth1 is not available.when i ifconfig -a,i can not see the eth0 and eth1, only lo0 and si0. Unlike to the other server i found eth0 and eth1 files in
/etc/sysconfig/network-scripts/.
what will i do? (2 Replies)
Discussion started by: kenshinhimura
2 Replies
10. IP Networking
Hi there guys!
I have a small task that I have to accomplish, but I don't seem to be able to do that.
I have a server that I don't have physical access to, and I mostly control it with webmin. The server is running 2 websites. Both of these websites have their own domains that are linked to... (1 Reply)
Discussion started by: D-Lexy
1 Replies