10 More Discussions You Might Find Interesting
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 126.96.36.199/24 188.8.131.52 1
add net 184.108.40.206/24: gateway... (2 Replies)
Discussion started by: aggadtech08
4. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
5. Red Hat
I have a machine with an interface that has two different addresses on CentOS 5
If I issue this command I get the result I'm looking for.
/sbin/route add -net 220.127.116.11 netmask 255.255.255.0 gw 10.20.21.77
ip route show dev eth0
18.104.22.168/24... (1 Reply)
Discussion started by: beaker457
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 22.214.171.124 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 126.96.36.199 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
7. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
9. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller