IPv6 Problems


Login or Register for Dates, Times and to Reply

 
Thread Tools Search this Thread
# 1  
IPv6 Problems

I am trying to setup an IPv6 network.

I modified the interfaces file:

Code:
/etc/network/interfaces
# The loopback network interface
auto lo
iface lo inet loopback

iface etho0 inet static
        address 2620:7:a000::1
        netmask 64
        gateway  ::ffff:c0a8:101

ifconfig shows this
Code:
root@server1:/home/server1# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:23:ae:27:b9:ec  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:16 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:6306 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6306 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:2114918 (2.0 MiB)  TX bytes:2114918 (2.0 MiB)

wlan0     Link encap:Ethernet  HWaddr 00:24:2c:49:d1:d8  
          inet addr:192.168.1.6  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::224:2cff:fe49:d1d8/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:97811 errors:0 dropped:0 overruns:0 frame:1779999
          TX packets:81649 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:56313143 (53.7 MiB)  TX bytes:15602876 (14.8 MiB)
          Interrupt:17 Base address:0xc000

netstat
Code:
netstat -r
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface
default         openrg.home     0.0.0.0         UG        0 0          0 wlan0
link-local      *               255.255.0.0     U         0 0          0 wlan0
192.168.1.0     *               255.255.255.0   U         0 0          0 wlan0


server1@server1:~$ netstat -rn -A inet6 
Kernel IPv6 routing table
Destination                    Next Hop                   Flag Met Ref Use If
::1/128                        ::                         U    256 0     0 lo
fe80::/64                      ::                         U    256 0     0 wlan0
::/0                           ::                         !n   -1  1  3755 lo
::1/128                        ::                         Un   0   4    47 lo
fe80::224:2cff:fe49:d1d8/128   ::                         Un   0   1     0 lo
ff00::/8                       ::                         U    256 0     0 wlan0
::/0                           ::                         !n   -1  1  3755 lo

ping6 to google
Code:
server1@server1:~$ ping6 ipv6.google.com
connect: Network is unreachable

ping6 to local host

Code:
server1@server1:~$ ping6  localhost
PING localhost(localhost) 56 data bytes
64 bytes from localhost: icmp_seq=1 ttl=64 time=0.066 ms
64 bytes from localhost: icmp_seq=2 ttl=64 time=0.088 ms
64 bytes from localhost: icmp_seq=3 ttl=64 time=0.080 ms
^C
--- localhost ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 1998ms
rtt min/avg/max/mdev = 0.066/0.078/0.088/0.009 ms

I am totally confused

To add to my confusion:

Code:
root@server1:/home/server1#  host -t AAAA www.cyberciti.biz
www.cyberciti.biz has no AAAA record


root@server1:/home/server1# lsmod | grep -qw ipv6 && echo "IPv6 kernel driver loaded and configured." || echo "IPv6 not configured and/or driver loaded on the system."
IPv6 not configured and/or driver loaded on the system.


root@server1:/home/server1# ip -6 addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qlen 1000
    inet6 fe80::224:2cff:fe49:d1d8/64 scope link 
       valid_lft forever preferred_lft forever


Last edited by Meow613; 10-05-2016 at 08:16 PM.. Reason: .
Login or Register for Dates, Times and to Reply

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

9 More Discussions You Might Find Interesting

1. Solaris

Solaris 10 IPv6

Hello Dears , please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface . Thanks in... (1 Reply)
Discussion started by: ttashman
1 Replies

2. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies

3. HP-UX

Ipv6 on hpux

my problem: i want to change from ipv4 to ipv6 on my home network. On hpux i can assign only address non routable as fe80::1 fe80::3 etc to my lan0 Editing netconf-ipv6 i can assing a routable ipv6 address like fd55:282f:3b98::/48 or 2001:470:26:307:89a0:aba1:f98b:eb3e but only to alias... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies

4. SuSE

Linux and IPv6

Hi gurus, In a few month, we must enable IPv6 on our Linux Server! Should we reinstall the Linux machine to enable IPv6 or could we just make some change in configuration's files? Could Linux run simultaneous IPv4 and IPv6? Thanks in advance for our help our ideas? Best regards, nm (3 Replies)
Discussion started by: hiddenshadow
3 Replies

5. Linux

ipv6 routing

I am trying to capture the ipv6 packets through pcap utility. For that i am redirecting the ipv6 packets to the loopback address , but the ipv6 packets are not getting redirected to tha loopback address.Instead they are taking there normal routes. (1 Reply)
Discussion started by: vikasmca05
1 Replies

6. IP Networking

IPv6 on Solaris 10

Hi! I have to configure ipv6 network between two computers with Solaris 10 but I not an expert in using any unix system and I do it becouse I need it to my study. Is someone here who could help me and describe step-by-step how to do it? please!!! PS. I need to configure network to do secure... (1 Reply)
Discussion started by: kolec
1 Replies

7. IP Networking

IPv6 testbed

Hello guyz.. did some of u have implement or making a testbed for IPv6? if yes, can u attached the procedures and standard guidelines because i really need for my proposal.. thanx.. (2 Replies)
Discussion started by: unknown2205
2 Replies

8. IP Networking

radvd + ipv6 problems in Linux

Hi everyone, I have a weird problem in Linux. Well, for the past month i've been very interested in IPv6, and, a couple of days ago i decided to try to get it to work. I run Slackware 8.0 on my gateway/router-box, and, the freenet6.com-program and scripts started and worked just fine. There's one... (1 Reply)
Discussion started by: kuba
1 Replies

9. IP Networking

Solaris IPv6

Hi, Anybody who worked with IPv6 on Solaris 8. I want to get rid of IPv6 (Uninstall). Any comments ...ideas...will be highly appreciated. (4 Replies)
Discussion started by: s_aamir
4 Replies

Featured Tech Videos