9 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
2. Red Hat
Hi..I have to change default gateway in my linux machine. Its OS is RHEL6.
I followed following steps.
1.run command ip route to check current default gateway
2.delete that gateway with command
route del default gw x.x.x.x eth2
3.Add new gatewy with command below
route add default gateway... (3 Replies)
Discussion started by: deljatt
3 Replies
3. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
4. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
5. HP-UX
where in configuration files can i modify default gateway in hp-ux11iv3 (5 Replies)
Discussion started by: h@foorsa.biz
5 Replies
6. AIX
Hi,
I have two interfaces on m AIX 5.3 box. One going to 192.168.1.x and it has a gateway of 192.168.1.1.
I configured the other gateway with 192.168.2.x and the default gateway as 192.168.2.1. But I can't get connectivity to the 192.168.2.1 network. Can someone help me out and let me know... (7 Replies)
Discussion started by: bbbngowc
7 Replies
7. IP Networking
i'm a real unix newbie, setting up a network, with a router to router vpn connection with a remote site, all the win stuff is talking and pinging and all the stuff it should be doing (yeah and crashing too, lol) but no communication with the unix box, i think the problem is with my default... (3 Replies)
Discussion started by: smcg
3 Replies
8. Solaris
my actual default gatewas IP is:
default 192.168.11.254
and I need to change it to 192.168.11.2, I'm using Solaris 9, how can i do it? and how i can save it in case that the machine restart and have the new default gateway IP saved? (5 Replies)
Discussion started by: Lestat
5 Replies
9. HP-UX
I am using HP-UX 11i and I need to add another default gateway.
how can I do that ? (3 Replies)
Discussion started by: salhoub
3 Replies
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)
NAME
traceroute6 -- print the route IPv6 packets will take to the destination
SYNOPSIS
traceroute6 [-dlnrv] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-m hoplimit
Specify maximum hoplimit.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-n Do not resolve numeric address to hostname.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r
-s src Src specifies the source IPv6 address to be used.
-v Be verbose.
-w waittime
Specify the delay time between probes.
RETURN VALUES
The traceroute6 command will exit with 0 on success, and non-zero on errors.
SEE ALSO
ping(8), ping6(8), traceroute(8)
HISTORY
The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD
May 17, 1998 BSD
