10 More Discussions You Might Find Interesting
1. AIX
Hello all,
Let me introduce about the context and my environment.
We have an AIX 6.1 system, it has 4 FC channels
/ > lsdev -Cc adapter | grep fcs
fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs2 Available 23-T1... (14 Replies)
Discussion started by: Phat
14 Replies
2. AIX
Hi guys,
I've been trying to tackle this issue for days and I'm stumped. Hopefully someone can give more light on what else I can do.
I have a p7 series box, with dual VIOS and 10 lpars and everything was working fine until I had to move the box to another location in the data centre. Ensured... (16 Replies)
Discussion started by: aixkidbee
16 Replies
3. Hardware
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Discussion started by: atahmass
1 Replies
4. IP Networking
Hello,
I have a pretty useless satellite link at home (far from any civilization), so I wanted to set up caching in order to speed things up. My Squid 2.6 runs "3128 transparent" and is set up quite well on a separate machine.
I also have my dd-wrt router to move all port 80 traffic through... (0 Replies)
Discussion started by: theWojtek
0 Replies
5. Solaris
Hi everyone,
I am hoping anyone of you could help me in this weird problem we have in 1 of our Solaris 10 servers. Lately, we have been having some ftp problems in this server. Though it can ping any server within the network, it seems that it can only ftp to a select few. For most servers, the... (4 Replies)
Discussion started by: labdakos
4 Replies
6. Solaris
Hi All,
I recently got a connection to the SAN through a fibre channel on my solaris box:
#luxadm -e port
/devices/pci@1d,700000/SUNW,qlc@1/fp@0,0:devctl CONNECTED
#ls -l /dev/cfg
lrwxrwxrwx 1 root root 48 Feb 23 12:31 c4 -> ../../devices/pci@1d,700000/SUNW,qlc@1/fp@0,0:fc
I then... (2 Replies)
Discussion started by: dede
2 Replies
7. AIX
Hello,
I have two systems that are being prepared to be SAN attached ..
can anyone tell me any specific checks I should perform prior to the cards being installed...
I am aware of firmware / OS level and relevant drivers, is there anything else?
thanks
Chris. (8 Replies)
Discussion started by: chlawren
8 Replies
8. Shell Programming and Scripting
Hi,
I have variables like mentioned below and want to separate as mentioned in output.
var1="4 x fibre cards"
var2="2 fibre cards"
var3="6 - fibre cards"
var4="4 x dual-port"
I have variables like this.I want to separate numbers from this and fibre cards from this.
output has to be... (4 Replies)
Discussion started by: ajilesh
4 Replies
9. AIX
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Discussion started by: Zim-Aix-Guru
4 Replies
10. UNIX for Advanced & Expert Users
Anyone know of a guide or instructions for Solaris
I got to configure a SBUS HBA to talk to a tape robot.
I have done this on a switch but not point to point.
just going HBA >>>>> TAPE Fibre simple two nodes
Kie (6 Replies)
Discussion started by: kie
6 Replies
squid_unix_group(8) System Manager's Manual squid_unix_group(8)
NAME
squid_unix_group - Squid UNIX Group external_acl helper
SYNOPSIS
squid_unix_group [-g groupname] [-g groupname...] [-p]
DESCRIPTION
This helper allows Squid to base access controls on users memberships in UNIX groups.
-g groupname
Specifies a group name to match.
-p Also match the users primary group from /etc/passwd
EXAMPLES
This squid.conf example defines two Squid acls. usergroup1 matches users in group1, and usergroup2 matches users in group2 or group3
external_acl_type unix_group %LOGIN /usr/local/squid/libexec/squid_unix_group -p
acl usergroup1 external unix_group group1
acl usergroup2 external unix_group group2 group3
NOTES
By default up to 11 groups can be matched in one acl (including commandline specified groups). This limit is defined by MAX_GROUPS in the
source code.
AUTHOR
This manual page was written by Henrik Nordstrom <hno@squid-cache.org>
squid_unix_group is written by Rodrigo Campos <rodrigo@geekbunker.org>
KNOWN ISSUES
Does not understand gid aliased groups sometimes used to work around groups size limitations. If you are using gid aliased groups then you
must specify each alias by name.
QUESTIONS
Any questions on usage can be sent to Squid Users <squid-users@squid-cache.org>
REPORTING BUGS
Report bugs or bug-fixes to Rodrigo Campos <rodrigo@geekbunker.org> or Squid Developers <squid-dev@squid-cache.org>
SEE ALSO
group(5),passwd(5)
Squid UNIX Group helper 12 August 2002 squid_unix_group(8)