10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
2. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
3. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
7. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
8. Solaris
Hi everybody,
One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled.
so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies
9. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
10. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
FIREWALLD.CONF(5) firewalld.conf FIREWALLD.CONF(5)
NAME
firewalld.conf - firewalld configuration file
SYNOPSIS
/etc/firewalld/firewalld.conf
DESCRIPTION
firewalld.conf is loaded by firewalld during the initialization process. The file contains the basic configuration options for firewalld.
OPTIONS
These are the options that can be set in the config file:
DefaultZone
This sets the default zone for connections or interfaces if the zone is not selected or specified by NetworkManager, initscripts or
command line tool. The default zone is public.
MinimalMark
For some firewall settings several rules are needed in different tables to be able to handle packets in the correct way. To achieve
that these packets are marked using the MARK target iptables(8) and ip6tables(8). With the MinimalMark option a block of marks can be
reserved for private use; only marks over this value are used. The default MinimalMark value is 100.
CleanupOnExit
If firewalld stops, it cleans up all firewall rules. Setting this option to no or false leaves the current firewall rules untouched.
The default value is yes or true.
Lockdown
If this option is enabled, firewall changes with the D-Bus interface will be limited to applications that are listed in the lockdown
whitelist (see firewalld.lockdownwhitelist(5)). The default value is no or false.
SEE ALSO
firewall-applet(1), firewalld(1), firewall-cmd(1), firewall-config(1), firewalld.conf(5), firewalld.direct(5), firewalld.icmptype(5),
firewalld.lockdown-whitelist(5), firewall-offline-cmd(1), firewalld.richlanguage(5), firewalld.service(5), firewalld.zone(5),
firewalld.zones(5)
NOTES
firewalld home page at fedorahosted.org:
http://fedorahosted.org/firewalld/
More documentation with examples:
http://fedoraproject.org/wiki/FirewallD
AUTHORS
Thomas Woerner <twoerner@redhat.com>
Developer
Jiri Popelka <jpopelka@redhat.com>
Developer
firewalld 0.3.9 FIREWALLD.CONF(5)