Quad Fast Ethernet Card on Sparc 10?

10 More Discussions You Might Find Interesting

1. Hardware

Best hardware for a fast local Ethernet?

Dear all, I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card. I would like to to measure the speed of data transmission between several servers that are going to be connected to the...

2. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres

3. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj

4. Solaris

quad card configuration

Hi Group, I Have just installed quad card in my V440 machine, I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able, here is details of my machine. ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 ...

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

6. Solaris

Quad Ethernet

I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me: SIOCSLIFFLAGS:...

7. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such...

8. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the...

9. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the...

10. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this?

LEARN ABOUT OSF1

ip6_setup

ip6_setup(8)						      System Manager's Manual						      ip6_setup(8)

NAME

       ip6_setup - IPv6 configuration program

SYNOPSIS

       /usr/sbin/ip6_setup

DESCRIPTION

       The ip6_setup utility allows you to configure the IPv6 networking software on your system.

       To run ip6_setup, enter the following command and then answer the questions: # ip6_setup

       You  must know your Internet Protocol Version 6 (IPv6) address. If your network uses subnet routing, you must know the subnet mask for your
       network.  The network manager should be able to provide you with the information that you need.

       After the ip6_setup command completes, the network services on the  system  can	be  restarted  manually  with  the  following  command:  #
       /usr/sbin/rcinet restart

       Before  you  restart  the  network  services  with  the preceding command, warn the users that the network services on the system are being
       removed.  File systems that were not mounted using the /etc/fstab file or the automount command must be unmounted with the unmount command.
       You must remount these file systems using the mount command after the network is started on your system.

       Alternatively, you can reboot the system with the following command: # /usr/sbin/shutdown -r now

FILES

       Specifies  the  host  name  file.  Specifies the environment variables that define the network configuration on your system.  Specifies the
       trusted hosts file.  Specifies the network name file.  Specifies Internet routing information.  Specifies Internet routing information.

SEE ALSO

       Commands: mount(8), rcinet(8)

       Files: gateways(4), hosts(4), hosts.equiv(4), networks(4), routes(4).

       Network Administration

																      ip6_setup(8)

IP Networking