Quad Fast Ethernet Card on Sparc 10?

Tags

10, 2.5, 5.3, configuration, created, directory, ethernet, fast, files, for each, host, hostname, hosts, interface, ip, ip address, ip networking, problem, reboot, run, set, sparc, stick, terminal, works

Special Forums IP Networking Quad Fast Ethernet Card on Sparc 10?

09-26-2002

Registered User

2, 0

Join Date: Sep 2002

Last Activity: 31 January 2003, 9:56 AM EST

Posts: 2

Thanks Given: 0

Thanked 0 Times in 0 Posts

Thk you i'll try, but for now I put a new Host name for the other eth, and it's work (it stay after reboot)
I have two eth under the same subnet and now I have problem to ping 2 switchs under the same subnet!!!!

Bye
Enzo

Quote:

Originally posted by RTM
Create a file in /etc with the following type of info:

file name
hostname.hmex where x is the interface number
hostname.qfex
hostname.lex

You have to know which interface type you have - grep them from the dmesg command

contents of file
xxx.xxx.xxx.xxx where xxx is your IP number OR
put the hostname in there but it must be /etc/hosts

Read the man pages for:
ifconfig
netmasks (section 4)
hosts (section 4)

croccopollo

View Public Profile for croccopollo

Find all posts by croccopollo

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Hardware

Best hardware for a fast local Ethernet?

Dear all, I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card. I would like to to measure the speed of data transmission between several servers that are going to be connected to the...

2. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres

3. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj

4. Solaris

quad card configuration

Hi Group, I Have just installed quad card in my V440 machine, I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able, here is details of my machine. ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 ...

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

6. Solaris

Quad Ethernet

I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me: SIOCSLIFFLAGS:...

7. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such...

8. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the...

9. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the...

10. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this?

LEARN ABOUT REDHAT

axnet_cs

AXNET_CS(4)						     Kernel Interfaces Manual						       AXNET_CS(4)

NAME

       axnet_cs - Asix AX88190 chipset PCMCIA Ethernet Driver

SYNOPSIS

       insmod axnet_cs.o [pc_debug=n] [irq_list=i,j,...]

DESCRIPTION

       Axnet_cs  is  a driver for PCMCIA ethernet cards based on the Asix AX88190 chipset.  These cards are mostly NE2000 compatible but have sev-
       eral bugs that are sufficiently tricky to work around that a separate driver was deemed necessary.  When this driver is bound to a card, it
       allocates  the  next  available	ethernet  device (eth0..eth#).	This device name will be reported in the kernel log file, and passed on to
       cardmgr(8).

PARAMETERS

       pc_debug=n
	      Selects the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.  A  non-zero
	      value enables debugging.

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver.

DIAGNOSTICS

       axnet_cs: this is not an AX88190 card!
	      Indicates that this card is probably a normal NE2000 compatible card, which requires the pcnet_cs driver.

       eth#: interrupt(s) dropped!
	      Indicates that the driver did not receive an interrupt notification for some reason.  The driver will poll the card (with a signifi-
	      cant performance penalty) if the problem persists.  The most likely cause is an interrupt conflict and/or host bridge  configuration
	      problem.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5).

pcmcia-cs							2001/08/17 12:51:58						       AXNET_CS(4)

IP Networking