Quad Fast Ethernet Card on Sparc 10?

10 More Discussions You Might Find Interesting

1. Hardware

Best hardware for a fast local Ethernet?

Dear all, I am setting up a new Ethernet network at home, I am going to have a good 100 Mbps internet connection (optic fiber) with a modem that have a gigabit ethernet card. I would like to to measure the speed of data transmission between several servers that are going to be connected to the...

2. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres

3. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj

4. Solaris

quad card configuration

Hi Group, I Have just installed quad card in my V440 machine, I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able, here is details of my machine. ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 ...

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

6. Solaris

Quad Ethernet

I have a Quad Ethernet card in a 220R. 2 ports activated. Each has its own hostname file and both hostnames are in the hosts file. I want both ports to have the same IP address so we can use the 2nd port in case we lose communication on the port. On bootup, the box gives me: SIOCSLIFFLAGS:...

7. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such...

8. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the...

9. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the...

10. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this?

LEARN ABOUT REDHAT

tc574_cs

3C574_CS(4)						     Kernel Interfaces Manual						       3C574_CS(4)

NAME

       3c574_cs - 3Com 3c574 Etherlink XL 10/100 PC Card device driver

SYNOPSIS

       insmod 3c574_cs.o [pc_debug=n] [if_port=n] [irq_list=i,j,...]  [full_duplex=n] [auto_polarity=n] [max_interrupt_work=n]

DESCRIPTION

       3c574_cs  is the low-level Card Services driver for the 3Com 3c574 EtherLink XL PCMCIA ethernet adapter.  When this driver is attached to a
       card, it allocates the next available ethernet device (eth0..eth#).  This device name will be reported in the kernel log file,  and  passed
       on to cardmgr(8).

       The  driver uses the N-Way autonegotiating transceiver to negotiate the speed and duplex of the network link.  If the link partner does not
       support negotiation, only the link speed is detected.

PARAMETERS

       pc_debug=n
	      Selects the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.  A  non-zero
	      value enables debugging.

       if_port=n
	      Selects  the  transceiver type.  Only 0, 1, and 4 are acceptable values, other values return an error.  This actual value specificed
	      is ignored -- the autonegotiating transceiver selects the media speed and duplex used.

       irq_list=i,j,...
	      This option limits the set of interrupts that may be allocated by this driver.  The default is all normally-usable IRQs.

       full_duplex=n
	      This flag determines if only full-duplex modes are advertised.  It defaults to 0 (false).

       This flag can be used to control the transceiver's auto polarity
	      detection capability.  Some Cisco Catalyst switches are known to interact badly with this feature in 10baseT mode.  It defaults to 1
	      (enabled).

       max_interrupt_work=work-limit
	      This  option  selects the maximum amount of work handled during each interrupt.  Each received packet counts as one unit of work, as
	      does updating statistics counters and handling errors.  The default is 32.

DIAGNOSTICS

       eth#: interrupt(s) dropped!
	      Indicates that the driver did not receive an interrupt notification for some reason.  The driver will poll the card (with a signifi-
	      cant  performance penalty) if the problem persists.  The most likely cause is an interrupt conflict and/or host bridge configuration
	      problem.

AUTHOR

       Driver core: Donald Becker - becker@scyld.com

       PC Card interface: David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5), ifport(8).

pcmcia-cs							       $Date							       3C574_CS(4)

IP Networking