Login or Register to Ask a Question and Join Our Community


IP Networking

route add

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Special Forums IP Networking route add
# 1  
Old 06-19-2010
route add
I have built a new linux server, via a iLo connection.

and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.

Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the server ?

Thank you
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. IP Networking

Add explicit route

Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254 if not working, please try gateway through management port: 10.128.55.254 Just want to double confirm if this would be the correct command #route add -net 10.128.255.41/32 10.128.201.254 And if didnt work #route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies

2. Solaris

Couldn't add route on Solaris 10

Hi Solaris Experts, I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node # netstat -rnv IRE Table: IPv4 Destination Mask Gateway Device Mxfrg Rtt Ref Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies

3. Solaris

Add route to solaris 10

I need to add a new route on solaris10 machine. I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway. How I do ? Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies

4. Solaris

Add route to solaris10

Hi need to add 2 routes, one on each server. I know the route add comand but I have always been given the parameters to put in. I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ? In... (6 Replies)
Discussion started by: vettec3
6 Replies

5. Solaris

route add : network is unreachable

Hey Guys: I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1 add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies

6. Solaris

Route Add

Hi, I am trying to add route command in Solaris 10 machine in the following fashion: route add -host 10.8.112.10 180.144.1.250 -interface lo0:1 this command fails with an error "lo0:1: bad value" I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies

7. IP Networking

Route add probleme

I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system. The ip i am trying to get to is 172.16.4.48 I need to get to it via the hme1 interface. The vpn gateway has this ip 172.30.50.1 I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies

8. HP-UX

Add Route on HP-UX v10.x, help.

Hi, My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13 I tried with: #route add 192.168.80.2 255.255.255.255 10.10.10.13 but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies

9. IP Networking

Do I need to add a route??

I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0. My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network. My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies

10. AIX

route add

Hello , We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ... #route add server.ip router.ip after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
Login or Register to Ask a Question

LEARN ABOUT MOJAVE

make_sockdfr

MAKE_SOCKDFR(8) 					      System Manager's Manual						   MAKE_SOCKDFR(8)

NAME

       make_sockdfr -  Generates frozen route file for SOCKS server

SYNOPSIS

       make_sockdfr [infile [outfile] ]

DESCRIPTION

       make_sockdfr reads in a plain-text route file for the SOCKS server and produces a frozen route file as the output.

       Both  arguments	are optional. The default for infile is /etc/sockd.route; the default for outfile is /etc/sockd.fr. You may specify infile
       while omitting outfile, but you cannot specify outfile without also speficying infile.

       The contents of the frozen route file is essentially the memory image of the parsed input file. Using the frozen route file can reduce  the
       start-up delay of the SOCKS server program since it no longer has to parse the file contents.

       When  the  SOCKS  server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to
       use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every  time	after  you
       modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file.

       To find out the contents of a frozen route file, use dump_sockdfr.

FILES

       /etc/sockd.fr, /etc/sockd.route

SEE ALSO

       dump_sockdfr(8), sockd.fr(5), sockd.route(5)

AUTHOR

       Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com

								    May 6, 1996 						   MAKE_SOCKDFR(8)