Login or Register to Ask a Question and Join Our Community


IP Networking

Maximum IP Address Configured on Intel Network Adapter

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Special Forums IP Networking Maximum IP Address Configured on Intel Network Adapter
# 1  
Old 10-07-2009
Data Maximum IP Address Configured on Intel Network Adapter
Hi All,

Sorry if this is not the correct forum to answer.
But hope somebody can help me...

For these two types of network adapter:
Intel(R) PRO/1000 MT Server Adapter
Intel(R) PRO/1000 MT Dual Port Network Adapter

How many IP addresses can be configured on it at the same time?

System is Windows 2000 Server.

Thanks
# 2  
Old 10-07-2009
It's not dependent on the NIC, but on how much the IP stack of the OS allows/can handle. One resource [ref] I found for that says
Quote:
Windows 2000, for example, can have at least hundreds of addresses assigned, but only 51 reliably work (51 total, spread out over all your nics, weather you have one or several). After the 52nd is added, Active Directory takes a dump and bad things happen.
# 3  
Old 10-07-2009
Hi Plundi,

Thanks for your response.
Do you think Windows 2000 here is Windows 2000 Server?

So if I asked to add 4 more IP addresses on 1 single network adapter(Intel(R) PRO/1000 MT Server Adapter), than it should be ok?[COLOR="#738fbf"]
# 4  
Old 10-07-2009
Since both are based on the same kernel (as far as I know), it's safe to assume that both share the same IP stack and it's limitations.

And 5 different IP addresses shouldn't be a problem for any modern server OS.
This User Gave Thanks to pludi For This Post:
wilsonSurya
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. SCO

Can not recognize network adapter SCO UNIX in HP z400

hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback. show message : dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies

2. Hardware

Problematic RTL8188EE Wireless Network Adapter

Good Day All, There are numerous results when searching google on this issue, however, none seem to have a solution. I have read until my eyes bleed and banged my head on the table more than once! :) I am hoping to resolve this issue -- or at least have a decent workaround. It is a real... (13 Replies)
Discussion started by: RogerBaran
13 Replies

3. IP Networking

Virtual Adapter MAC address..

Hi, I just want to know whether two MAC address can exist in a adapter.. I mean one there will be mandatory one And another as user defined one.. Any replies will be more helpful.. Please help.. :wall: (0 Replies)
Discussion started by: Priya Amaresh
0 Replies

4. UNIX for Dummies Questions & Answers

Simulated driver for Network Interface Adapter

Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean? - It has to run on all network adapters - It has to be as simple as it can be - It has to run on all linux distributions (or at least most of them) - It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies

5. UNIX for Dummies Questions & Answers

SCO Unixware 7.1.4 Network Adapter Error

Hi All I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached. I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies

6. UNIX for Dummies Questions & Answers

External Network Adapter for Solaris 10

Hi All, I am new here - this is my first post. I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies

7. AIX

How to active this network adapter?

When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command: entstat -all ent#|grep -i priority Priority: 5 Active: False How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies

8. AIX

change network adapter

hello i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 ) what i need to do after the new adapter installed on the machine? thanks best regards ariec (1 Reply)
Discussion started by: ariec
1 Replies

9. AIX

hacmp network adapter re-define

I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies

10. Solaris

Sun v440/v880 network adapter teaming

Is it possible to team two network adapters for fault tolerance in a Sun v440 or v880 Solaris 8 box? If so how would I go about doing so? (1 Reply)
Discussion started by: ghuber
1 Replies
Login or Register to Ask a Question