10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi All,
I have done IEEE 802.3ad Dynamic link aggregation bond configuration with name bond0 which has 4 slaves (each 25GB/s) in it on cent os 6.8. Issue i am facing is bonding throughput is only 50GB/s not 100GB/s. below are the configuration files :
DEVICE=bond0
IPADDR=xx.xx.xx.xx... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
2. IP Networking
Hey Guys,
Does anybody know, which OID's of Net-SNMP is used to collect throughput and bandwith usage of machine??
I got these OID's
..iso.org.dod.internet.mgmt.mib-2.interfaces.ifTable.ifEntry.ifOutOctets
..1.3.6.1.2.1.2.2.1.16
... (1 Reply)
Discussion started by: franzramadhan
1 Replies
3. IP Networking
Hello,
First time poster here hoping to get some help with ns2.
I've recently started using ns2(first time user) but I'm having difficulty getting the results I'm after.
I am trying to set up a network with wireless nodes(5-15 nodes) and then use xgraph to display a timing diagram,... (0 Replies)
Discussion started by: UnicksMan
0 Replies
4. Solaris
Hello gurus,
I have the following configuration in the server side:
# dladm show-aggr
key: 33 (0x0021) policy: L4 address: 0:14:4f:6c:11:8 (auto)
device address speed duplex link state
nxge0 0:14:4f:6c:11:8 1000 Mbps ... (3 Replies)
Discussion started by: FERCA
3 Replies
5. Solaris
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
6. IP Networking
I have a 10Gbps network link connecting two machines A and B. I want to transfer 20GB data from A to B using TCP. With default setting, I can use 50% bandwidth. How to improve the throughput? Is there any way to make throughput as close to 10Gbps as possible? thanks~ :) (3 Replies)
Discussion started by: andrewust
3 Replies
7. SCO
I just (re)installed SCO6 here from scratch because I am hunting a problem. So, I installed it, then got the SCO OpenServer Release 6.0.0 Maintenance Pack 4 Device Drivers Supplement .iso and installed the nd package.
# mount -F cdfs /dev/cd0 /cd-rom
# pkgadd -d /cd-rom
Then elect the nd... (2 Replies)
Discussion started by: dalek
2 Replies
8. UNIX for Advanced & Expert Users
Was wonder if there was a tool or program I could run to measure throughput on our CentoS 4.x server. Our current dedicated host provider is charging us by how much throughput we are using and I just want to see if their numbers add up to whatever I get using a throughput tool of some kind.
... (6 Replies)
Discussion started by: mcraul
6 Replies
9. UNIX for Advanced & Expert Users
Is there a tool or cmd line program i can use to test my tape throughput in Mb/sec?
thank you (2 Replies)
Discussion started by: progressdll
2 Replies
10. Solaris
How can I tell on Solaris 9 sparc if my nics are running 100 gigabit full duplex... (4 Replies)
Discussion started by: csaunders
4 Replies
