10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello Forum,
I have prepared script to monitor the tomcat status.
Following is the script which will monitor tomcat instance.
I need little modifcation in the script.
My script will grep for process,
the output of grep command will analyze by if condition under for loop and will send... (2 Replies)
Discussion started by: ooilinlove
2 Replies
2. IP Networking
Dear gurus of Linux / Unix.
I have a server, which I use to monitoring traffic, the problem that I find is when I run the following command:
probe:~ # sar -n DEV 1
I see that I one second appear info in some interface and in the other second no appear, I don't know what will be the... (0 Replies)
Discussion started by: andresguillen
0 Replies
3. Solaris
I have been instructed to disable the finger service for our Solaris 10 box. However when I input #svcadm disable finger I receive: "svcadm: Pattern 'finger' does not match any instances. I have also tried to edit the inetd config file and comment out the finger part but Solaris has basically... (14 Replies)
Discussion started by: mvhoward
14 Replies
4. Shell Programming and Scripting
Hi All,
I am creating df monitoring script. but facing some below problm.
Please see the below code.
df_threshold=90;
for i in `cat df_fnl.txt`
do
if ; then
echo "%df is more than $df_threshold "
fi
done (6 Replies)
Discussion started by: aish11
6 Replies
5. Linux
hello,
i'm having some performance problem on one of my linux machines and i hope someone will be able to help me analyzing the problem.
machine info:
Linux fedora, cpu x 4 cores of 1.6Ghz, 8G memory, 8G swap.
i've enabled sar on my machine and created a graph using ksar utility for... (15 Replies)
Discussion started by: levic
15 Replies
6. Shell Programming and Scripting
Hi,
I am new to shell programming,
I would like to write a script which will monitor sendmail service in linux, and if service goes down it will send the mail
can you please suggest me how to monitor the service?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
7. Solaris
hi all,
i am trying to enable pool service
but i recive this message
-bash-3.00# pooladm
pooladm: couldn't open pools state file: Facility is not active
-bash-3.00# pooladm -e
svcadm: Instance "svc:/system/pools:default" is in maintenance state.
pooladm: cannot enable pools:... (4 Replies)
Discussion started by: corvinusbsd
4 Replies
8. Linux
Hi guys,
please help me out my smartd service is not being up.
$ sudo /sbin/service smartd restart
Shutting down smartd:
Starting smartd:
$
Take a look of /etc/smartd.conf
/dev/sda -H -m... (1 Reply)
Discussion started by: daya.pandit
1 Replies
9. AIX
Dear All,
When i am start the service netd i am facing the problem
0513-015 The inetd Subsystem could not be started
Please check subsystem resources and try again later.
please suggest me.
It is urgent (1 Reply)
Discussion started by: pernasivam
1 Replies
10. Filesystems, Disks and Memory
Hi all,
I am looking for api to get me system monitoring statictics every 5 minutes.
I am looking at the following statistics:
1. System CPU Usage
2. Process CPU Usage
3. Process Memory Usage
4. I/O Usage for a certain disk.
5. Process I/O bytes/sec utilization.
I have seen very... (2 Replies)
Discussion started by: uiqbal
2 Replies