10 More Discussions You Might Find Interesting
OK group, it's been 12 years since I worked with SCO. I need some direction here:
SCO Openserver 5.07
I have a server with a bad motherboard. I have moved the SCSI adapter and hard drive to another computer. This new server has different hardware so I must install the chipset drivers for... (1 Reply)
Discussion started by: jscholz
PCI-X was popular years ago, now it's not. Today's motherboards have PCIe slots, not PCI-X slots. I'm accustomed to using Adaptec, but I believe they've been bought out by ATTO Technology. Now ATTO has a product called PCI UL50 Dual Channel VHDCI Ultra320 SCSI PCIe card. So: does the SCO UNIX... (7 Replies)
Discussion started by: Transpower
I am at a loss with a VIO server running ios 188.8.131.52-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable:
name physloc ... (4 Replies)
Discussion started by: johnf
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
I need to connect 80pin SCA Ultra320 SCSI hdd to 68pin.
There are rumors that some bad "passive" adapters with problematic termination can fry the HDD. The adapter we got is Assmann ABSCA-2. Hard drive is 'Fujitsu MAW3073NC'
Do we need to set any jumpers before turning it on?
We already had... (0 Replies)
Discussion started by: orange47
I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
I have 1 PCI-X Dual Channel Ultra320 SCSI Adapter card for my p570 server. I would like to split the 2 channels for the usage of 2 tape drives in different LPARs. Is that possible?
For example, I have 2 LPARs running in p570 server, LPAR-A configured the Ultra320 card as pci7 in slot... (11 Replies)
Discussion started by: kwliew999
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
10. UNIX for Dummies Questions & Answers
Can anyone out there help me out? I'm trying to install a scsi tape back up on a sys running sco openserver 5.0.4. When I go through the steps for mkdev tape it seems like it works, but when I reboot I still don't see the tape. Also when it boots up I get a scsi bios not installed error. I've... (1 Reply)
Discussion started by: goatboy_tx
CE(4) BSD/i386 Kernel Interfaces Manual CE(4)
ce -- driver for synchronous Cronyx Tau-PCI/32 WAN adapters
To compile this driver into the kernel, place the following line in your kernel configuration file:
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
The ce driver needs either sppp(4) or netgraph(4). Which one to use is determined by the NETGRAPH_CRONYX option. If this option is present
in your kernel configuration file, the ce driver will be compiled with netgraph(4) support. Otherwise, it will be compiled with sppp(4) sup-
Refer to sconfig(8) for information about the ce adapter configuration.
The ce driver supports the following models of Tau-PCI/32 WAN adapters:
Cronyx Tau-PCI/32 two fractional/unframed E1 interfaces, with 32 HDLC channels shared between them with total adapter throughput 2048
single fractional/unframed E1 interface, with 32 HDLC channels.
cp(4), ctau(4), cx(4), sppp(4), ifconfig(8), sconfig(8), spppcontrol(8)
The ce driver was added in FreeBSD 6.2, FreeBSD 5.5 and FreeBSD 4.11. The ce driver for previous versions of FreeBSD is available from
BSD January 30, 2006 BSD