Today (Saturday) We will make some minor tuning adjustments to MySQL.

You may experience 2 up to 10 seconds "glitch time" when we restart MySQL. We expect to make these adjustments around 1AM Eastern Daylight Saving Time (EDT) US.

HPUX 11.11 Sept.2003 cannot see PCI-X scsi adapter

Login or Register to Reply

Thread Tools Search this Thread
# 1  
HPUX 11.11 Sept.2003 cannot see PCI-X scsi adapter

I am trying to reload a RP4440 with 2x300gb disks and dual Port Network card, with HPUX 11.11 Sept 2003. When the os boots and and gets to the main menu to install HPUX or run recovery, it cannot find the disks or NIC.
At the OS prompt (after loading files), ioscan shows the Class ba, and shows PCI-X SCSI and the Ethernet as an UNKNOWN sub-Class of ba, even though it loads the PCI-X Bus Adapters and loads the BA Class for the slots.
In the /tmp/ it generates does not, of course, have any listing for the disk.
1) can the disk string be manually added eventhough ioscan sees unknow, or do I Have to find a newer release of 11.11 somewhere/somehow?

------ Post updated at 11:28 AM ------

sorry, it is the release I was using.

Last edited by mrmurdock; 08-30-2018 at 02:28 PM..
Login or Register to Reply

Thread Tools Search this Thread
Search this Thread:
Advanced Search

More UNIX and Linux Forum Topics You Might Find Helpful
NPIV with 8Gb PCI Express Dual Port FC Adapter
All I am at a loss with a VIO server running ios SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable: $ lsnports name physloc ...... AIX
SCSI Ultra320 80->68 adapter
I need to connect 80pin SCA Ultra320 SCSI hdd to 68pin. There are rumors that some bad "passive" adapters with problematic termination can fry the HDD. The adapter we got is Assmann ABSCA-2. Hard drive is 'Fujitsu MAW3073NC' Do we need to set any jumpers before turning it on? We already had...... Hardware
Spliting PCI-X Dual Channel Ultra320 SCSI Adapter
I have 1 PCI-X Dual Channel Ultra320 SCSI Adapter card for my p570 server. I would like to split the 2 channels for the usage of 2 tape drives in different LPARs. Is that possible? For example, I have 2 LPARs running in p570 server, LPAR-A configured the Ultra320 card as pci7 in slot...... AIX
Which SCSI Adapter?
Plain Person
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy. I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this...... Solaris
adaptec scsi host adapter
Can anyone out there help me out? I'm trying to install a scsi tape back up on a sys running sco openserver 5.0.4. When I go through the steps for mkdev tape it seems like it works, but when I reboot I still don't see the tape. Also when it boots up I get a scsi bios not installed error. I've...... UNIX for Dummies Questions & Answers
UNIX for Dummies Questions & Answers
CP(4)							 BSD/i386 Kernel Interfaces Manual						     CP(4)

cp -- driver for synchronous Cronyx Tau-PCI WAN adapters
To compile this driver into the kernel, place the following line in your kernel configuration file: device cp Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_cp_load="YES" Additional options: device sppp options NETGRAPH options NETGRAPH_CRONYX
The cp driver needs either sppp(4) or netgraph(4). Which one to use is determined by the NETGRAPH_CRONYX option. If this option is present in your kernel configuration file, the cp driver will be compiled with netgraph(4) support. Otherwise, it will be compiled with sppp(4) sup- port. Refer to sconfig(8) for information about the cp adapter configuration.
The cp driver supports the following models of Tau-PCI WAN adapters: Cronyx Tau-PCI V.35 and RS-232 interfaces Cronyx Tau-PCI/R RS-530(RS-449) and X.21 interfaces Cronyx Tau-PCI-L one V.35 and RS-232 interface, low profile Cronyx Tau-PCI-L/R one RS-530(RS-449) and X.21 interface, low profile Cronyx Tau-PCI-E1 fractional E1 interfaces Cronyx Tau-PCI-G703 unframed E1 interfaces Cronyx Tau-PCI-2E1 fractional E1 and unframed E1 interfaces Cronyx Tau-PCI-4E1 fractional E1 and unframed E1 interfaces Cronyx Tau-PCI-E3 E3 interface Cronyx Tau-PCI-T3 T3 interface Cronyx Tau-PCI-STS1 STS-1 interface
ctau(4), cx(4), sppp(4), ifconfig(8), sconfig(8), spppcontrol(8)
The cp driver was added in FreeBSD 5.3 and FreeBSD 4.11. The cp driver for previous versions of FreeBSD is available from
July 16, 2005 BSD

Featured Tech Videos