When I login to the live console of my server and go to the console, I am getting the below message
Code:
Processor is booting from the first available device.
To discontinue, press any key within 10 seconds.
10 seconds expired.
Proceeding...
Trying Primary Boot Path
------------------------
Booting...
Boot IO Dependent Code (IODC) revision 0
HARD Booted.
ISL Revision A.00.44 Mar 12, 2003
ISL booting hpux
Firmware Version 44.24
Duplex Console IO Dependent Code (IODC) revision 1
Firmware Version 44.24
Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
(c) Copyright 1995-2004, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State CoProcessor State Cache Size
Number State Inst Data
--------- -------- --------------------- ----------------- ------------
0 1000 MHz Active Functional 33554432 33554432
1 1000 MHz Idle Functional 33554432 33554432
2 1000 MHz Idle Functional 33554432 33554432
3 1000 MHz Idle Functional 33554432 33554432
Central Bus Speed (in MHz) : 200
Available Memory : 8388268 KB
Good Memory Required : Not initialized. Defaults to 32 MB.
Primary boot path: 0/4/1/1.3
Alternate boot path: 0/0/2/0.3
Console path: 0/7/1/1.0
Keyboard path: 0/0/4/0.0
WARNING: The BMC System Event Log (SEL) is full.
Use MP SL command to clear space so SEL events can be recorded.
ERROR: There was not enough error free memory to run the
CPU late selftests. Refer to the Page Deallocation
Table in the service menu to review memory errors.
This message is coming over and over again in the Console logs.
And in the system Events I have got this entry coming frequently.
Code:
# Location|Alert| Encoded Field | Data Field | Keyword / Timestamp
-------------------------------------------------------------------------------
0 SFW 0 *5 0xA080132000E00010 0000000000000000 BOOT_NOT_ENOUGH_ERROR_FREE_MEMORY
28 Nov 2013 13:20:21
So id you havent changed anything before the last reboot ( compiled a new kernel? ) then the message says it all
Code:
WARNING: The BMC System Event Log (SEL) is full.
Use MP SL command to clear space so SEL events can be recorded.
I never had to configure a RP3440 so I dont remember what its using (GSP or MP) The closest I got is a
Code:
ant:/home/vbe $ model
9000/800/L2000-54
having a gsp...
But both (gsp or mp) should work the same way, you may need to do some search...
On the console I used to type ctrl-B and I get to the gsp console which would display something like Service Processor Login: Since I never configured them I'd press <enter> and you get the GSP prompt: GDP > type h for help...
SL is for show log - I dont remember how you remove them ( Years since last time I went there...) maybe just looking at them sufiice... So look carefullly at the menu and the help...
Then you would type co to return to the OS console.. Its my supprt dispatch week so sorry cant spend more time with you... will try to follow though and if I have a moment...
Good Luck!
So id you havent changed anything before the last reboot ( compiled a new kernel? ) then the message says it all
Code:
WARNING: The BMC System Event Log (SEL) is full.
Use MP SL command to clear space so SEL events can be recorded.
I never had to configure a RP3440 so I dont remember what its using (GSP or MP) The closest I got is a
Code:
ant:/home/vbe $ model
9000/800/L2000-54
having a gsp...
But both (gsp or mp) should work the same way, you may need to do some search...
On the console I used to type ctrl-B and I get to the gsp console which would display something like Service Processor Login: Since I never configured them I'd press <enter> and you get the GSP prompt: GDP > type h for help...
SL is for show log - I dont remember how you remove them ( Years since last time I went there...) maybe just looking at them sufiice... So look carefullly at the menu and the help...
Then you would type co to return to the OS console.. Its my supprt dispatch week so sorry cant spend more time with you... will try to follow though and if I have a moment...
Good Luck!
So id you havent changed anything before the last reboot ( compiled a new kernel? ) then the message says it all
Code:
WARNING: The BMC System Event Log (SEL) is full.
Use MP SL command to clear space so SEL events can be recorded.
I have already cleared the logs. But still I am getting the same error. And after sometime the logs again gets filled and I am back to the start again.
Hi Guys,
I have a small problem with a v445 which I have been informed will only boot with the reconfigure option enabled.
It is attached to HP SAN storage using qla2300 FCA's with a Veritas encapsulated rootvoldg (No Laughing here please) when I try a reboot I get the following error.
... (5 Replies)
HPUX running in D-Class (L1000), pretty old HPUX version - hpux 11.00
Attempt 1 -- To boot from normal (primary)
Unable to boot - system complains failure
SYSTEM ALERT System Name : uninitialized DATE : 10/22/2011 Time : 03/41:12 Alert Level 15 = Fatal hardware or configuration... (12 Replies)
I'm trying to run clusterKnoppix live cd from a couple machines but it only works from one computer. The other three, my toshiba laptop, emachine, and hp machine can't find the filesystem.. the live cd stops booting and gives me a error saying it couldn't find knoppix filesystem and then gives me a... (0 Replies)
hi
SCO Unix 5.0.6 doesn't boot due to this problem:
not a directory
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot
Knows someone howto solve it? (16 Replies)
I have installed Solaris 10 OS in Sun Virtual Box that uses x86 32 bit system. After an abnormal shutdown i'm getting the following message on the console when i try to boot.
SunOS Release 5.10 Version Generic_127128_11 32-bit
Copyright 1983-200 Sun Microsystems, Inc. All rights reserrved.
Use... (3 Replies)
I installed solaris virtually and tried to format the partitions .. I dont know what went wrong, It got rebooted and hangs in the screen "No partitions" and after pressing Enter button it goes to "INT18 boot failure" and hangs there once again . Could any one of you suggest why this has happened... (3 Replies)
Hi all
I used a dual boot operating system and it works fine for me. Now , i install a Ati radeon 9250 Agp card on my system and this results in boot failure of fedora 6. The graphics card is working fine with windows XP , i.e i have no compatibility issues.The system also refuses to boot when i... (2 Replies)
Hello.
System is a HP Visualize C3600 running X11 and after a power failure machine will not boot (see error messages below)
From what I've read, this may be caused by a corrupted etc/inittab file. Solution suggested on other websites is to boot in single user mode and edit file inittab... (2 Replies)
