Login or Register to Ask a Question and Join Our Community


HP-UX

Polling target on Serviceguard

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems HP-UX Polling target on Serviceguard
# 1  
Old 06-11-2012
Polling target on Serviceguard
Hi Guys,

we are planning to enable polling target on our SG in reference to this link

MC/ServiceGuard: Subnet Goes Down when one of the Cluster Node is Down - HP Customer Care (United States - English)

since our server is already in production can we apply the changes with ex. "cmapplyconf -v -C cmclconfig.ascii" without any downtime to SG?
# 2  
Old 06-19-2012
From an old training manual I have, as of release 11.17 changing IP addresses for heartbeats or monitored subnets, requires the cluster to not be running.

The only cluster changes that could be made with the cluster running, were adding/deleting a node, changing max configured packages, and access control modifications.

If you have a newer version, I don't know what still applies.
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. Linux

Volume is mounted on two ServiceGuard nodes

Hey! I'm running a HP ServiceGuard cluster with three nodes. One of the packages was moved (not by me) from one node to another a few weeks ago. I just noticed that one of the volume groups is still mounted on the old node. Oops! When I run df, less space is used on the old node than the new. ... (0 Replies)
Discussion started by: tobiasvl
0 Replies

2. HP-UX

After adding new iscsi target port, still the session state of that target port is showing offline

Hi, I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result ... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies

3. HP-UX

Install Patch on ServiceGuard environment

I have two hpux11iv1 on ServiceGuard. I need to backup my hpux 11iv1 by EMC backup software. but before i install client agent, i need to install two software patch: 1. J4256AA HP-UX IPSec 2. IPv6NCF11i HP-UX 11iv1 IPv6 I wantna know if i installed two software patch have any impact? or... (5 Replies)
Discussion started by: cooljack123
5 Replies

4. Programming

Db polling...

Hi! Im trying to make a program that polls a mysqlDB every 5 minutes. the poll checks a scheduletable in the dB and exicutes a function if there was a "go" in the scheduletable, and if it retrives a "no go" from the table it should just wait for another 5 minutes before re polling the DB, ... (1 Reply)
Discussion started by: karlblau
1 Replies

5. HP-UX

Serviceguard Extension for RAC

Dear All, From where to download freeware of Serviceguard Extension for RAC software for HP UNIX PA RISC B.11.11 OS. BR, Prasanth (3 Replies)
Discussion started by: prasanth438
3 Replies

6. HP-UX

need to recall my hp serviceguard clustering

hi, do u know any link that will get back to me up to speed on hp serviceguard on clustering? thanks and much appreciated, itik (2 Replies)
Discussion started by: itik
2 Replies

7. HP-UX

MC Serviceguard and WebSphere ND 6.1

I am a Lawson Software consultant assisting a client with a Lawson upgrade. One of our components is WebSphere Application Server ND 6.1. Our client is using MC Serviceguard for failover. When testing failover, my Websphere instance is trying to start, but generating this error, referencing the old... (4 Replies)
Discussion started by: mrvitas
4 Replies

8. HP-UX

Serviceguard Cluster Questions..

Hi, I'm fairly new to HP-UX. I am trying to find out if it is possible to create a cluster with 3 active nodes and 1 passive node. Everything I have found online so far just describes active/active and active/passive. Is it possible to have 3 active nodes and 1 passive node in a cluster? If... (2 Replies)
Discussion started by: DtbCollumb
2 Replies

9. HP-UX

HP Serviceguard failover - what doesn't get moved across?

Excuse the basic nature of the question, I've zero experience with regards to this and I'm just looking for a little clarity... When using serviceguard for a failover from one machine to another, what doesn't get taken from one machine to the other? For example, I was told that OS users and... (1 Reply)
Discussion started by: stefcha
1 Replies

10. HP-UX

ServiceGuard on HP-UX 11.23 Mission Critical

Dear(s), anybody have played ServiceGuard on HP-UX version 11.23 MC ? I am planning to install Oracle and OpenView Operations for Unix 8 on a ServiceGuard clustered HP-UX environment, any suggestionsfrom where should I start ? Best Regards, Mostafa Reda (1 Reply)
Discussion started by: darousha
1 Replies
Login or Register to Ask a Question