9 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Team,
Presently I have a script, which i have set up cron on one of my Jump-boxes,and gives me the output on every hourly basis,fetching the data from the remote machine.Basically it gives me the list of all active users logged and its count once we execute the script.Here the count is... (6 Replies)
Discussion started by: whizkidash
6 Replies
2. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
3. UNIX for Dummies Questions & Answers
I have scheduled couple of shell scripts to run using 'at' command.
The o/p of at -l is:
$ at -l
1320904800.a Thu Nov 10 01:00:00 2011
1320894000.a Wed Nov 9 22:00:00 2011
1320876000.a Wed Nov 9 17:00:00 2011
$ uname -a
SunOS dc2prcrptetl2 5.9 Generic_122300-54 sun4u sparc... (2 Replies)
Discussion started by: superparticle
2 Replies
4. IP Networking
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Discussion started by: mghis
3 Replies
5. Solaris
Hi,
/sbin/ifconfig -a
when i login as guest user , output like below,
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet... (5 Replies)
Discussion started by: forumguest
5 Replies
6. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
7. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
8. Solaris
Hi All,
I have an interface port configured to a FBOL server. This port receives requests from various hosts. I want to know at any moment of time ip addresses of all those hosts from which the requests are coming in. Please help me with command/script. (2 Replies)
Discussion started by: digitalrg
2 Replies
9. Solaris
Given a new Solaris box, with a fresh, unconfigured install on it, how does one figure out what kind of network interface it has (bge,le, hme, etc)? (8 Replies)
Discussion started by: akbar
8 Replies