I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches.
On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular Card (with RJ45) the network drops!
Can the second NIC rely on the first one? What are logical connections??
Any help??
Thanks
That will be two distinct comms interfaces. There is no failover mechanism.
Try "lanscan" to see what is LAN cards are fitted and to find out each "lanN" number then run "ifconfig lanN" to find out whether the LAN card in question is configured with an IP address. If not, it is a case of deconfiguring the fibre card and configuring the card in question with an IP address. If I was doing this I would change the IP address of the fibre card to an unused address then insert the original IP address into the card in question.
Changes to IP comms are best done from the physical console while using an adjacent workstation for tests.
Be sure to save this file before making any changes:
I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table?
I don't know how to do this.:confused: (9 Replies)
I found an old post that talks about 2 nice cards and it is driven by the IP address .... but I didn't understand it because the 2 people skipped information for me the newbie..
Can someone help me... I have the proxy server setup and I believe I have enabled the 2nd nic card, I just need one... (1 Reply)
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Hi,
What is the best reference that gives in detail on nic cards configuration , assigning multiple ip addresses to a single interface, netlink library etc and all basic stuff at this level..?
Thanks (2 Replies)
We have a setup of two nodes which has two NIC cards in each. One is built in and another is D-Link (external NIC card). We are unable to ping to the external NIC cards in both. Eg: Node A has two IPs 192.168.1.10 (eth0) and 192.168.2.10 (eth1) and Node B has two IPs 192.168.1.20 (eth0) and... (3 Replies)
I am running HP_UX 11.23 with 4 NIC cards (this is our TSM server)
I have 4 subnets we are backing across. trying to keep traffic on their subnets. I only have one route statment should I add more.
route add net 123.99.8.0 netmask 255.255.255.0 123.99.8.254
route add net 123.99.67.0 netmask... (2 Replies)
Hello
I have 2 machines with 3 NIC cards.
When I setup veritas, I receive this message:
e1000g1 has an IP address configured on it. It could be a public NIC on ken.
Are you sure you want to use e1000g1 for the first private heartbeat link?
As if e1000g1 should not have an IP address.... (2 Replies)
Hi;
I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now... (2 Replies)
I need to add a PCI NIC to a sunblade 100 running solaris 8. Im new to this and was hoping someone could give me some card names and models which will work for this system and has a driver for this sparc system.
thanks (3 Replies)
