8 More Discussions You Might Find Interesting
1. Solaris
I have installed Solaris 11 Express on my machine. On my GA-X58A-UD5 motherboard there are two 6 Gb/s SATA ports (Marvell 9128 chip), but when I connect a hard drive to one of them, the system does not recognize it.
However, when I boot from a USB install image (downloaded from here Oracle... (1 Reply)
Discussion started by: RychnD
1 Replies
2. Hardware
I have an upgrade path in mind for a new computer that will be stocked with a 2TB SATA 300 hard disk. This is a choice based on information that SATA 300 is not necessarily faster than SATA 600. The upgrade path in a year time or so would then involve the purchase of an SSD that would contain the... (4 Replies)
Discussion started by: figaro
4 Replies
3. Hardware
Hello everybody,
I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors.
The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies
4. UNIX for Advanced & Expert Users
trying to setup a sata drive using a sata to scsi adaptor
I have a sata 1TB Deskstar that I had setup before and during shipment from a facilty to another, the disk failed. The handling was not great, lots of throwing boxes, etc. I have a new disk from Hitachi (thankyou Hitachi) anyway, I don't... (1 Reply)
Discussion started by: mndavies
1 Replies
5. UNIX for Advanced & Expert Users
Hi,
I have two sata hard-disks. Out of those, one is having RHEL5 operating system, and other is having fedora7 operating system.
When I connect the disk with RHEL5 operating system to sata0 port and disk with fedora7 operating system to sata1 port. While booting it shows RHEL5 boot screen,... (3 Replies)
Discussion started by: praveen_b744
3 Replies
6. Shell Programming and Scripting
hi
how floppy disks, CDs and flash drives (pen drives) are accessed in UNIX?
thanks (0 Replies)
Discussion started by: nokia1100
0 Replies
7. UNIX for Advanced & Expert Users
i have a system which has two hard disks..one is sata and the other one is normal ata hard disk.
i wish to install red hat enterprise linux WS(desktop edition) on my sata hard disk..but the installer shows me only my ata hard disk..
i searched the net..it says that a library-- libata will let it... (2 Replies)
Discussion started by: ankit.jss
2 Replies
8. Solaris
can any one help me look for a driver for SATA harddisk, im installing solaris 9 to it.
thanks and regards
msouthofheavenk ;) (2 Replies)
Discussion started by: msouthofheavenk
2 Replies
AAC(4) BSD Kernel Interfaces Manual AAC(4)
NAME
aac -- Adaptec AdvancedRAID Controller driver
SYNOPSIS
aac* at pci? dev ? function ?
ld* at aac? unit ?
DESCRIPTION
The aac driver provides support for the Adaptec AAC family of SCSI and SATA RAID controllers. These controllers support RAID 0, 1, 5, 10,
and volume sets. They have four channels in the add-in version or 1-2 channels in the motherboard integrated version, and are most often
found rebadged by Dell, Hewlett-Packard or IBM. Supported controllers include:
o Adaptec AAC-364
o Adaptec SCSI RAID 2120S
o Adaptec SCSI RAID 2200S
o Adaptec SATA RAID 2410SA
o Adaptec SATA RAID 3405
o Adaptec SCSI RAID 5400S
o Dell PERC 2/Si
o Dell PERC 2/QC
o Dell PERC 3/Di
o Dell PERC 3/Si
o Dell PERC 320/DC
o Dell CERC SATA RAID 1.5/6ch
o HP NetRAID 4M
o HP ML110 G2 (Adaptec SATA RAID 2610SA)
o IBM ServeRAID 8k
Access to RAID containers is available via the ld device driver. Individual drives cannot be accessed unless they are part of a container or
volume set, and non-fixed disks cannot be accessed. Containers can be configured by using the on-board BIOS utility of the card.
DIAGNOSTICS
The adapter can send status and alert messages asynchronously to the driver. These messages are printed on the system console.
SEE ALSO
intro(4), ld(4)
HISTORY
The aac driver first appeared in NetBSD 1.6, and was based on the FreeBSD driver of the same name.
BUGS
This driver is not compatible with controllers that have version 1.x firmware. The firmware version is the same as the kernel version
printed in the BIOS POST and driver attach messages.
BSD
February 19, 2011 BSD