M5000 won't power up

 
Thread Tools Search this Thread
Special Forums Hardware M5000 won't power up
# 1  
Old 06-19-2018
M5000 won't power up

on an m5000 , I can not power it up, system failure.

Code:
XSCF> poweron -a
DomainIDs to power on:00,01
Continue? [y|n] :y
00 :Not powering on :Poweron canceled due to missing component.
01 :Not powering on :Poweron canceled due to missing component.


the only fault that I can see is:

Code:
 DDC_A#0 Status:Deconfigured;
*       DDC_A#1 Status:Deconfigured;
*       DDC_A#2 Status:Deconfigured;
*       DDC_A#3 Status:Deconfigured;
*       DDC_B#0 Status:Deconfigured;
*       DDC_B#1 Status:Faulted;
*   IOU#0 Status:Deconfigured;
*       DDC_A#0 Status:Deconfigured;
*       DDCR Status:Deconfigured;
*           DDC_B#0 Status:Deconfigured;
*   IOU#1 Status:Deconfigured;
*       DDC_A#0 Status:Deconfigured;
*       DDCR Status:Deconfigured;
*           DDC_B#0 Status:Deconfigured;


but I can not find a part number?

and the board give faulted?

Code:
XSCF> showboards -a
  
 XSB  DID(LSB) Assignment  Pwr  Conn Conf Test    Fault    
---- -------- ----------- ---- ---- ---- ------- -------- 
00-0 00(00)   Assigned    n    n    n    Passed  Faulted  
00-1 01(04)   Assigned    n    n    n    Passed  Faulted  
00-2 01(05)   Assigned    n    n    n    Passed  Faulted  
00-3 01(06)   Assigned    n    n    n    Passed  Faulted  
01-0 01(00)   Assigned    n    n    n    Passed  Faulted  
01-1 01(01)   Assigned    n    n    n    Passed  Faulted  
01-2 01(02)   Assigned    n    n    n    Passed  Faulted  
01-3 01(03)   Assigned    n    n    n    Passed  Faulted


do I need a new motherboard, or just the one piece that faulted?

Last edited by rbatte1; 06-19-2018 at 08:58 AM.. Reason: Added CODE tags for all output for clarity (and disabling the smilies)
# 2  
Old 06-19-2018
Do you have support for the M5000? I would say replacing the faulted part should be enough. You can also try to reset the fault and try again to powerup the system. But go slowly with a poweron -d 0 first and see what happens. If domain 0 is running, you can try to start domain 1.
This User Gave Thanks to DukeNuke2 For This Post:
# 3  
Old 06-19-2018
no support since its older. just a company that swaps parts. I did try the power on each domain and same result , did no reset fault, what command does that? I will try and find it.
# 4  
Old 06-19-2018
Sun shipped some mobo's in COD (Capacity on Demand) mode which means they won't work without a license. Have you got one of those? Do you know the machine history?

Search the web for:
"Capacity on Demand"
This User Gave Thanks to hicksd8 For This Post:
# 5  
Old 06-19-2018
Quote:
Originally Posted by goya
no support since its older. just a company that swaps parts. I did try the power on each domain and same result , did no reset fault, what command does that? I will try and find it.
From the XSCF use the command version -c xcp and send the output. Depending on the version you might not be able to reset the error...
This User Gave Thanks to DukeNuke2 For This Post:
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Beginners Questions & Answers

Bash script won't run because hardware won't produce display

Can anyone offer any advice on how to modify the script below to work on a new system we have, that has no graphics capability? We admin the system through a serial RAS device. I've tried running the below script through the RAS and through an ssh -X session. It failed with something like "GTK... (3 Replies)
Discussion started by: yelirt5
3 Replies

2. AIX

IBM Power 740 won't boot after firmware update

A team member installed the wrong version of License Code on a Power 740 system used in our Development environment. The system will no longer boot. Does anyone have IBM documentation or experience to share on recovering a system that currently reports "Unsupported License Code version... (1 Reply)
Discussion started by: kevinedailey
1 Replies

3. Solaris

M5000 fails to boot

I have an m5000 that Is down. I have access to XSCF> and was able to get to the ok prompt. However, on >ok boot it failed to boot. erred with : svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL. Nov 29... (3 Replies)
Discussion started by: goya
3 Replies

4. IP Networking

M5000 Xscf

I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip. it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out. so my question is, any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies

5. Hardware

Sun/Oracle M5000 Question

I have an M5K with disk issues I'm trying to troubleshoot, and it's causing me some confusion. I know the host has four on-board HDDs, but the format command's output shows c0t0d0, c0t1d0, c3t0d0, and c3t1d0. cfgadm -al shows c0t3d0 as the DVD-ROM drive, and c1 and c2 as SAN disks. Confused yet? ... (2 Replies)
Discussion started by: desertdenizen
2 Replies

6. Solaris

Unable to start SunVTS on M5000

Please advise. Thank you bash-3.00# cd /usr/sunvts/bin/ bash-3.00# ls bios.bin iobushangscript.sh stopsunvts vtsprobe cmos.bin javabridge.jar sunlink vtsreportgenerate dispatcher loadVtsServer svmVolDiskList vtstalk env6test... (6 Replies)
Discussion started by: incredible
6 Replies

7. Solaris

M5000 Question

Hi i 've a M5000 running 2 domains in my Lab with following hardconf SPARC Enterprise M5000; Memory_Size:128 GB; +-----------------------------------+------------+ | FRU | Quantity | +-----------------------------------+------------+ | MBU_B... (3 Replies)
Discussion started by: fugitive
3 Replies

8. Solaris

M5000 Question

Hi, I 've a fully loaded M5000 which i would like to partition in 4 domains but i have a concern that since we have only 4 internal disks how can we partition the box in for domains with 2 disks ( mirrored ) in each domain. Should i go ahead with 1 Lun from SAN and 1 internal disk for each of 4... (3 Replies)
Discussion started by: fugitive
3 Replies

9. AIX

won't mount /usr...won't boot fully

Hello: NOOB here. I attempted to use smit mkcd. Failed on first attempt, not enough space. 2nd attempt tried to place iso on /usr, not enough space there. Cleanup ran for about 5 minutes after aborting. Now AIX won't boot. LCD display on 7029-6E3 says: 0517 MOUNT /USR. Attempted to boot from CD... (11 Replies)
Discussion started by: bbird
11 Replies
Login or Register to Ask a Question