Visit Our UNIX and Linux User Community

Cooler GPU

Thread Tools Search this Thread
Special Forums Hardware Cooler GPU
# 1  
Old 09-01-2014
Cooler GPU

In one of our computers a Zotac GPU was installed (Zotac GeForce GTX 780 3GB AMP! to be exact) and the processor remained an Intel Core i7 2600. For the processor a new after-market cooler was installed and for the GPU also, together with fans on all case grids.
Initially the temperatures as measured on the CPU were around 70C to 75C. However, after performing a software upgrade on the install stack, temperatures suddenly dropped to 40C to 45C, with no noticeable drop in performance. No other changes were made, the machine is connected as it was before, in the same location etc.

What could have caused the drop in operating temperatures?
# 2  
Old 09-01-2014
75C is dangerously high. I wouldn't be surprised if it was into thermal throttling at that point.

Reducing the clockspeed could let it run at a similar pitch without thermal throttling.

It also depends what was in the 'software upgrade'. Any operating system components in there? Could have been misreading the temperature. Or you might be misreading it now, reading case/board temp while your cores are still cooked to the edge of oblivion.
# 3  
Old 09-02-2014
We did encounter shutdowns a few times, particularly when the temperature would enter the 80C+ region.
The upgrade indeed involved one from Centos 6.5 to Centos 7, so an answer may lie in there. No shutdowns as of yet either.

Also, I just confirmed that we are actually measuring core temperature, ie 4 measurements every 5 mins, one for each core.

I am not sure if we can adjust the clockspeed, given that the CPU is boxed.
# 4  
Old 10-24-2014
Newer kernels include more support for CPU throttling, C-states. Probably stepping down the CPU when it can. What kind of load is the system usually under? Honestly even if your CPU is pegged 100% 24/7 you shouldnt be in 75-80C. Thats way too hot. 60C is where you want to be for a non-overclocked CPU even at 100% duty cycle. 30-45 for idle or normal use.

There is an entry in the kernel cpu config to enable or disable turbo speeds. ( not overclocking specifically) Maybe the old config happened to have that enabled, and the new one is disabled by default?

Not that you can compare to values pre-upgrade, but two things to look at that might be of use is to check the physical power usage of the box with a power-meter inline from the socket to the PSU. They can be had for $20-30. Again, not all that usefull without having "before" values to compare too. But more info on your system is always good to have. Second thing to look at is install "turbostat". It will show you the clock-rates and precentage of time each core is spending in various C states ( full power through idle/power-save modes). There are a handful of other tools that show the same info. Thats just the one I happened to use recently.
This User Gave Thanks to agentrnge For This Post:
# 5  
Old 12-01-2014
For the record, the upgrade from Centos 6.5 to Centos 7 was performed again and we have been experiencing no higher temperature than 45C, routinely lower than 40C. This is the case for the last two months, so problem seems solved.

Previous Thread | Next Thread
Test Your Knowledge in Computers #684
Difficulty: Medium
According to both NetMarketShare and WikiMedia, Safari claimed a mobile market share of over 40% in 2019.
True or False?

6 More Discussions You Might Find Interesting

1. Linux

Vfio passtrough gpu, a question about hdmi

The situation videocard n1 Nvidia Ge-force(used on host linux) videocard n2 Ati radeon(used on guest windows 7) host is Slackware 14.2,kernel 4.18.15 I had set vfio to pass a ati card to windows7 guest Configure /etc/modprobe.d/vfio.conf options vfio-pci... (1 Reply)
Discussion started by: Linusolaradm1
1 Replies

2. Hardware

How disabling GPU?

Hi All I'm find out a way to disable the DGD: AMD Radeon HD 7470M on my Ubutu 16.04.2 LTS because radeon open source module is not capable to support this GPU and consequence the boot is very slow. I have tried serveral way with pci-stub.ids in the grub menu but not work. In general how... (11 Replies)
Discussion started by: _Fabio_79
11 Replies

3. Hardware

CUDA GPU terminates process at random instances

I am trying to start troubleshooting an error on a virtual server that uses the ubuntu 14.04 OS. Basically what happens (seeming random) is that the GPU stops processing and terminates. What Imean by seeming random is that for 3 runs there is no error then on run 4 the error appears. It has... (2 Replies)
Discussion started by: cmccabe
2 Replies

4. Hardware

External GPU issue

Dear all, I set up a external Gforce GPU using the PE4H (Pcie passive adapter) from HWTOOLS.NET. I'm able to add and remove the device doing and The point is the kernel does not initialized the device correctly. Here is what dmesg gives after the scan: lspci -t gives and lspci... (2 Replies)
Discussion started by: aihake
2 Replies

5. UNIX for Advanced & Expert Users


Hi , i want begin programming using CUDA which enviroment can i get .I don't have desktop to buy GPU graphics card. what should to do to get CUDA enviroment. i'm thinking to buy desktop has this card or laptop (1 Reply)
Discussion started by: Scotch
1 Replies

6. Solaris

Tracing the GPU usage

Hello, Can give me some tips to trace the GPU usage on a solaris8 update7 box? I try to understand why a Cadcam app is so slow on my Solaris box compared to a win$ box. I guess it comes from the poor graphic card I have but i would like to emphasize it. My bench is 150sec long on a Solaris... (0 Replies)
Discussion started by: solea
0 Replies

Featured Tech Videos