10 More Discussions You Might Find Interesting
1. Red Hat
Hi All,
I have a new x3650 M4 server with hardware RAID 5 configured 4 x 300 GB (HDD).
The Raid controller is ServeRAID M5110e.
Im getting "device not found" error during hardisk detection of RHEL6 install using DVD.
Some pages over the net pointed to using ServerGuide media for... (1 Reply)
Discussion started by: Solaris_Begin
1 Replies
2. SuSE
Hi all,
I am currently using opensuse 12.1,
We have Raid 5 array of 8 disks. A friend of mine accidently removed a drive & place it back and also added a new disk to it(making it 9 disks). now the output of mdadm --detail is as shown below
si64:/dev # mdadm --detail /dev/md3
/dev/md3:... (1 Reply)
Discussion started by: patilrajashekar
1 Replies
3. UNIX for Advanced & Expert Users
Hi there,
Don't know if my title is relevant but I'm dealing with dangerous materials that I don't really know and I'm very afraid to mess anything up.
I have a Debian 5.0.4 server with 4 x 1TB hard drives.
I have the following mdstat
Personalities :
md1 : active raid1 sda1 sdd1... (3 Replies)
Discussion started by: chebarbudo
3 Replies
4. AIX
Hi,
I have a filesystem that is created on a VG with 12 disks. The FS is striped on these disks. Now I have to add 10 more disks to this volume group to help increase the space of the same FS that is striped. How should I add these disks to the Vg and i need these disks to be added such the FS... (1 Reply)
Discussion started by: aixromeo
1 Replies
5. AIX
Hello all.
I have a volume group with 8 PV's, and a logical volume striped across these 8 volumes.
However, an lslv is showing:
STRIPE WIDTH: 9
STRIPE SIZE: 64k
There's really only eight disks, so how can the stripe width be 9?
ODM also showed this:
# odmget CuAt |... (4 Replies)
Discussion started by: Scott
4 Replies
6. AIX
Hi,
I have an ssa filesystem to move to san. We don't want any downtime. I heard that you can do a mirroring of existing file system on the san. The file system is a type of either raid 0, raid 1, or raid 5.
Anyone know how to do this?
Thanks in advance,
itik (4 Replies)
Discussion started by: itik
4 Replies
7. Solaris
VxVM:
How to add one more disk into v08 the stripe should change from 7/128 to 8/128
v v08 - ENABLED ACTIVE 8954292224 SELECT v08-01 fsgen
pl v08-01 v08 ENABLED ACTIVE 8954292480 STRIPE 7/128 RW
sd bkpdg35-01 v08-01 bkpdg35 17216 ... (0 Replies)
Discussion started by: geoffry
0 Replies
8. Solaris
I have one volume raid5 with 3 slice one of them is maintenance state. I replace this slice and resync the volume. when I try to mount the file system another slice goes to last erred. Again resync and the state goes to OK but the slice in mantenance persist. I try to enabled this but persist in... (2 Replies)
Discussion started by: usdsia
2 Replies
9. SCO
Forgive me, I do not know much about RAID so I'm going to be
as detailed as possible.
This morning, our server's alarm was going. I found that one
of our drives have failed. (we have 3)
It is an Adaptec ATA RAID 2400A controller
I'm purchasing a new SCSI drive today. My questions:
... (2 Replies)
Discussion started by: gseyforth
2 Replies
10. Programming
Is there a way in c to find out if a binary program contains debug information?
I have tried to compare the striped and unstriped versions of two programs,
but i have had a hard time understand them. (2 Replies)
Discussion started by: shienarier
2 Replies