10 More Discussions You Might Find Interesting
1. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
2. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
3. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
4. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
5. Solaris
Hi,
we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side.
... (1 Reply)
Discussion started by: manni2
1 Replies
6. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
7. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
8. SCO
Hi,
I have my server which has LAN with above model build onboard my Dell Server, I got this driver from SCO Unix website but yet to identify the following option:
1. PCI Slot-
2. Bus-
3. Device-
4. Function-
Would anyone please kindly advice what should the... (0 Replies)
Discussion started by: spiderweb
0 Replies
9. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
10. AIX
I am posting this as an FYI. I burned a lot of time on digging for this solution. The problem was performance between newer AIX p series boxes and a sun 4500 with a fiber nic. I tried many misc. solutions but this turned out to fix the issue. My bandwidth benchmark went from around 20MB/sec to... (1 Reply)
Discussion started by: chuckw
1 Replies