10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I'm new to RAID although I've had a server running raid5 for a while. It was delivered preinstalled like this and I never really wondered how to monitor and maintain it. This quick introduction just to let you understand why I'm such an idiot asking such a silly question.
Now what... (0 Replies)
Discussion started by: chebarbudo
2. UNIX for Advanced & Expert Users
I have been trying to create a USB RAID 5 using mdadm tool on Joli OS 1.2 (Ubuntu) but with no luck. I cannot even get pass the creation of array device (/dev/md0) and superblock. I am using 3 USB keys (2 16.4 GB kingston and 1 16GB sandisk).
My steps are:
... (5 Replies)
Discussion started by: powelltallen
3. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
4. Red Hat
had this RHEL 5 installation with /dev/sda1 and /dev/sda2 running..
created two more partitions /dev/sdj1 and /dev/sdj2 , the same sized partition as /dev/sda
trying to use mdadm to create RAID1 ..
I cannot even do it in "rescue" mode, I wonder if it can be done..
it kept... (2 Replies)
Discussion started by: ppchu99
5. UNIX for Advanced & Expert Users
I am not sure if I understand how mdadm --create /dev/md0 --level=container works?
A device called /dev/md0 appears in /proc/mdstat but I am not sure how to use that device?
I have 2 blank drives with 1 500GB partition on each. I would like to setup mirroring, but not in the... (0 Replies)
Discussion started by: hytron
6. UNIX for Advanced & Expert Users
Hello, I have 4 drives (500G each) in a raid 10, I got a power failior and this is the result?
md126 : inactive sdb sdc sdd sde
1953536528 blocks super external:-md127/0
md127 : inactive sdd(S) sde(S) sdb(S) sdc(S)
9028 blocks super... (3 Replies)
Discussion started by: rmokros
7. Emergency UNIX and Linux Support
I have a RAID 5 array consisting of 4 drives that had a partial drive failure in one of the drives.
Rebooting shows the faulty drive as background rebuilding and mdadm /dev/ARRAYID shows three drives as in sync with the fourth drive as spare rebuilding.
However the array won't come... (9 Replies)
Discussion started by: Bashingaway
8. Virtualization and Cloud Computing
Hello Unix Community:
My task to figure out how to add a 20G volume to an existing EBS Array (RAID0) at AWS.
I haven't been told that growing the existing volumes isn't an option, or adding another larger volume to the existing array is the way to go. The client's existing data-store is... (0 Replies)
Discussion started by: Habitual
I have a three disk raid 5, with 500GB disks.
This is close to being full, and whilst I can just add another disk and rebuild to add another 500GB, I would prefer to replace with 1TB disks. So i have some questions.
Can I replace these disks one by one with bigger disks? I... (1 Reply)
Discussion started by: snoop2048
I am using gmake to compile a c program with a makefile. The make file runs ld. I get the following error
jsh1035c:/users/egate453/admegate/kapil/samples $ gmake -e -f GNUmakefile queue_c
gmake -f ./GNUmakefile queue_c in_objdir=1 build_root=/users/egate453/admegate/kapil/samples... (2 Replies)
Discussion started by: handak9
sasl_errors(3) SASL man pages sasl_errors(3)
sasl_errors - SASL error codes
The following are the general error codes that may be returned by calls into the SASL library, and their meanings (that may vary slightly
based on context):
Common Result Codes
Another step is needed in authentication
Memory shortage failure
Mechanism not supported / No mechanisms matched requirements
Bad / Invalid Protocol or Protocol cancel
Can't request information / Not applicable until later in exchange
Invalid Parameter Supplied
Transient Failure (e.g. weak key)
Integrity Check Failed
SASL library not initialized
Client-only Result Codes
Needs user interaction
Server failed mutual authentication step
Mechanism does not support requested feature
Server-only Result Codes
Mechanism too weak for this user
Encryption needed to use mechanism
One time use of a plaintext password will enable requested mechanism for user
Passphrase expired, must be reset
User Not Found
Version mismatch with plug-in
USer exists, but no verifier for user
Password Setting Result Codes
Requested change was not needed
Passphrase is too week for security policy.
User supplied passwords are not permitted
SASL 10 July 2001 sasl_errors(3)