Partition management: lvm? fdisk? parted? (on RAID)


 
Thread Tools Search this Thread
Special Forums Hardware Filesystems, Disks and Memory Partition management: lvm? fdisk? parted? (on RAID)
# 1  
Old 04-30-2010
Partition management: lvm? fdisk? parted? (on RAID)

Hello,

I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?).

It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume.

I want to break that partition up into at least two separate ones. What I am wondering is:

* What's the difference between using fdisk and parted? Any reason to use one over the other?

* Should I just use lvm instead to shrink the current volume and create a second one? Is there a down-side to use logical volumes without creating a physical partition with fdisk/parted?

* Being that there are already two disks in RAID 1 configuration, does partitioning with lvm or fdisk/parted transparently propagate to the mirror disk or do I need to do something to partition BOTH drives?

Thanks in advance!!
# 2  
Old 05-03-2010
Quote:
Originally Posted by builder88
I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?).
Run
Code:
lsmod | grep raid

If you get a result, and the last number in the line is not 0, it's probably a software RAID.
Quote:
Originally Posted by builder88
It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume.

I want to break that partition up into at least two separate ones.
Why? The idea of LVM is that you don't have to juggle around with partitions, but can crate volumes as needed.
Quote:
Originally Posted by builder88
* What's the difference between using fdisk and parted? Any reason to use one over the other?
Both modify the partition table. parted is more user-friendly, while fdisk is more scriptable, and an experienced user is probably faster using fdisk than parted.
Quote:
Originally Posted by builder88
* Should I just use lvm instead to shrink the current volume and create a second one? Is there a down-side to use logical volumes without creating a physical partition with fdisk/parted?
If you want to create an additional partition, you should without question first backup and check the backup, and only then:
  • shrink the filesystem(s) in the LVM
  • shrink the logical volumes
  • shrink the volume group
  • repartition.
Quote:
Originally Posted by builder88
* Being that there are already two disks in RAID 1 configuration, does partitioning with lvm or fdisk/parted transparently propagate to the mirror disk or do I need to do something to partition BOTH drives?
That's more or less the whole idea behind a mirrored disk setup, that changes are done to both sides in case one fails.

Before you start making any changes and fsck up the machine, read up on Logical volume management, LVM, and RAID.
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Using parted command to create LVM partitions

Oracle Linux 6.6 To create Physical Volumes for Volume groups (LVM) , the disk need to be partitioned to LVM type ie. 'Linux LVM' type . In fdisk , this can done by choosing 8e when prompted for partition type. Since it is easy to script (non-interactive), I use parted command rather than... (1 Reply)
Discussion started by: John K
1 Replies

2. UNIX for Dummies Questions & Answers

RAID autodetect in fdisk -l

Hello, Please refer to the below output: # fdisk -l /dev/sda Disk /dev/sda: 598.9 GB, 598999040000 bytes 255 heads, 63 sectors/track, 72824 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * ... (1 Reply)
Discussion started by: admin_db
1 Replies

3. Red Hat

Shrink LVM partition & create new Linux Primary partition

Hello All, I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows, /boot - Linux Partition & another is LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc). Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies

4. Red Hat

Can I change the partition type with fdisk without disrupting data?

Hello, I have been going through our environment and I see we have a few servers with LVM's setup and the file system type is still set to "83" within fdisk. If I change this to "8e", will it hurt the data or cause any loss? I need to know for sure before I make the change. (1 Reply)
Discussion started by: s ladd
1 Replies

5. Shell Programming and Scripting

Non-interactive fdisk partition in script

Hi, How can I run fdisk partition in a script without interactive input? In manual procedure, I run fdisk device, select n, select p, presess enter for default start number (1), press enter to default end number, then select w for writing to the partition table. The command looks like... (3 Replies)
Discussion started by: hce
3 Replies

6. UNIX for Dummies Questions & Answers

How to convert non LVM root partition to LVM?

Hi Guys, I m using redhat 6, I have installed root partition as non-LVM . Is there any way i can convert it to LVM? (1 Reply)
Discussion started by: pinga123
1 Replies

7. Shell Programming and Scripting

Partition with parted

Hello folks, I have 2.4TB san storage i want to make 4 partition each having 600GB. I use fdisk but not possible to do this because of fdisk limitation. So i tried parted but it make 2.4TB one partition but with parted not possible to make 4 partition having 600GB, may be i m doing wrong, can... (6 Replies)
Discussion started by: learnbash
6 Replies

8. UNIX for Dummies Questions & Answers

Fdisk v/s parted

Just started understanding linux filesystem and partition utilities. I was going though some video tutorials by CBT nuggets and the author was cursing fdisk as fuzzy tool and recommending to use parted instead. In our job environment i have seen almost every one using fdisk utility for... (1 Reply)
Discussion started by: pinga123
1 Replies

9. UNIX for Dummies Questions & Answers

I've created a partition with GNU Parted, how do I mount the partition?

I've created a partition with GNU Parted, how do I mount the partition? The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards. Thanks, --Todd (1 Reply)
Discussion started by: jtp51
1 Replies

10. Solaris

recovery partition table from fdisk?

I have two disks on a sun blade 100. I just installed a solaris8 on the first disk. The installation was successful. But the problem is now I lost all data / partition on my second hard disk. The possible reason could be: 1. I used default web start install. During the installation I didn't... (2 Replies)
Discussion started by: motor98
2 Replies
Login or Register to Ask a Question