Login or Register to Ask a Question and Join Our Community


IPSec - VPN using shared key


 
Thread Tools Search this Thread
Special Forums Cybersecurity IPSec - VPN using shared key
# 1  
Old 02-04-2003
IPSec - VPN using shared key

Hello! I have some trouble trying to configure a VPN with two gateways. One of them uses IPSec [FreeSwan/Linux] with a single key, 256bits length, specified in /etc/ipsec.secrets. As FreeSwan manual page says, if i put esp=3des-md5-96, will be used a "64bit IV key (internally generated), a 192bit 3des ekey and a 128bit hmac-md5 akey (RFC2451, RFC2403). The part I miss is: how can i split this key to be able to set up the other gateway with OpenBSD/FreeBSD? Or what must be done to use this single key for encryption and authentication on the xBSD gw? Here is a part from ipsec.conf:
Code:
conn my_connection
	left=[left_ip]
	...
	right=[right_ip]
	esp=3des-md5-96
	keyexchange=ike
	keylife=4h
	auto=start

and from ipsec.secrets:
Code:
left_ip right_ip : 0xaabccdd_eeffgghh_...

Thanks,
# 2  
Old 02-04-2003
You don't need to 'split the key'... the key (shared secret) is symmetric, not asymmetric. You simply use the same (shared secret) key on both ends of the IPSEC VPN tunnel.

Each end will use the (shared secret) key to generate a session key.
# 3  
Old 02-11-2003
My real problem is that the Linux gateway is using a "pre-shared ke", while the xBSD gateway is asking different keys with different encryption styles: encryption key and auth key. That i did not figure out: why BSD needs different keys and FreeSWAN/ipsec does not, or how can a BSD gateway talk to a FreeSWAN/Linux gateway with PSK?
# 4  
Old 02-11-2003
Perhaps you would be better off using a simple shared secret between the two implementations. This shared secret would be used to establish a session key.

Did you try this to see if it would work? Did you establish a tunnel with only shared secrets (this is called a pre-shared key in the article below)?

http://www.onlamp.com/lpt/a/3043

Also, see the following article on setting up a BSD-LINUX IPSEC tunnel:

http://home.t-online.de/home/hburde/ipsec/node1.html
Login or Register to Ask a Question

Previous Thread | Next Thread

8 More Discussions You Might Find Interesting

1. IP Networking

Best tool to monitor VPN IPSEC Tunneling

We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug. Please suggest what may be the cause for the above mentioned issue. Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity. (4 Replies)
Discussion started by: marunmeera
4 Replies

2. IP Networking

IPSec Openswan Site to Site VPN - Big Pain

Hi @all, I try to connect 2 LANs with IPSec/Openswan LAN 1: 192.168.0.0/24 LAN 2: 192.168.1.0/24 This is my Config: conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies

3. IP Networking

VPN IPSec Openswan

Hi all, I have installed Openswan and configured IPSec and works perfect, but for some unknown reasons it stop working. I see that the tunnels are up and established. The route to the destination are added. Everything by the book seems to be ok. But somehow when i start to ping the other side (... (4 Replies)
Discussion started by: ivancd
4 Replies

4. Programming

Shared library with acces to shared memory.

Hello. I am new to this forum and I would like to ask for advice about low level POSIX programming. I have to implement a POSIX compliant C shared library. A file will have some variables and the shared library will have some functions which need those variables. There is one special... (5 Replies)
Discussion started by: iamjag
5 Replies

5. Cybersecurity

IPSEC

hello, after configuration ipsec in ip4 I can not ping between client and server whereas I had success ping before configuration! I also generate different key for AH and ESP as i have shown below. what is my problem and what should i do to have ping and test the configuration? code: ... (0 Replies)
Discussion started by: elinaz
0 Replies

6. Solaris

Solaris 8 ssh public key authentication issue - Server refused our key

Hi, I've used the following way to set ssh public key authentication and it is working fine on Solaris 10, RedHat Linux and SuSE Linux servers without any problem. But I got error 'Server refused our key' on Solaris 8 system. Solaris 8 uses SSH2 too. Why? Please help. Thanks. ... (1 Reply)
Discussion started by: aixlover
1 Replies

7. IP Networking

IPSec VPN Routing

Hello, I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue. ... (0 Replies)
Discussion started by: salukibob
0 Replies

8. UNIX for Advanced & Expert Users

How to interpret the shared memory key

I'm facing a problem interpreting the shared memory key on an AIX machine. (1) I go to a property file and I see the following: shm_key = "119112066" (2) So I now go the command prompt and do this: ipcs -m | grep 119112066 And, I do not find it. So what I do is to run the... (2 Replies)
Discussion started by: vijaygade
2 Replies
Login or Register to Ask a Question

Featured Tech Videos