NIM w/ two network interfaces


Login or Register for Dates, Times and to Reply

 
Thread Tools Search this Thread
# 1  
Question NIM w/ two network interfaces

Hi all, this is my first post on this forum. My main problem is this:

I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing. I have made a few mistakes doing this. I want to force all 10.x.x.x traffic over the Admin VLAN and everything else can go over the SUMA interface. That way all of the other AIX boxes and admins can come in on en4 and SUMA and all other packets go to the en8. I used route add and when i rebooted I lost all of my routing, I know that it isn't persistent now! I have used smitty to do a lot of the changes the problem w/ that is that it puts multiple entries into the ODM. Not good messes up the routing table. Here is what I have right now:

Route Tree for Protocol Family 2 (Internet):
10/8 10.156.40.1 UG 5 3660 en4 - -
10.155.40.0 10.155.40.16 UHSb 0 0 en8 - - =>
10.155.40/24 10.155.40.16 U 0 1 en8 - -
10.155.40.16 127.0.0.1 UGHS 0 1 lo0 - -
10.155.40.255 10.155.40.16 UHSb 0 4 en8 - -
10.156.40/24 10.156.40.20 U 1 107459 en4 - -
10.156.40.20 127.0.0.1 UGHS 5 77 lo0 - -
10.156.40.255 10.156.40.20 UHSb 0 4 en4 - -
127/8 127.0.0.1 U 13 171177 lo0 - -

I just need to force all 10.x.x.x over the internal en4 interface, shouldn't be that hard right? Yet I need both interfaces to know where their default gateways are... Maybe I am just missing a step, that is what I am thinking. Any help would be great.
# 2  
closed because of double posting.

bakunin
Login or Register for Dates, Times and to Reply

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

Test Your Knowledge in Computers #878
Difficulty: Medium
Memory allocation is less critical in a real-time operating system (RTOS) than in other operating systems.
True or False?

10 More Discussions You Might Find Interesting

1. Linux

Network interfaces error

I just ran sudo service networking start on Ubuntu 16.00 and came out with error message Job for networking service failed because control process exited with error code see systemctl status networking.service I tried to also run this command systemctl status networking.service I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies

2. UNIX for Dummies Questions & Answers

/etc/network/interfaces

i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help (1 Reply)
Discussion started by: g0dlik3
1 Replies

3. UNIX for Advanced & Expert Users

How to bond network interfaces

All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies

4. Debian

/etc/network/interfaces problem

Hello i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address then i save it wq! then i restart the networking , /etc/init.d/networking restart . but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies

5. UNIX for Dummies Questions & Answers

using wget on selected network interfaces

Hi there, I have a Linux Debian server with 2 network cards each connected through a different gateway : auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.224 netmask 255.255.255.0 gateway 192.168.1.1 auto eth1 iface eth1 inet... (5 Replies)
Discussion started by: chebarbudo
5 Replies

6. Solaris

Network Interfaces

I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies

7. AIX

NIM w/ two network interfaces

Hi all, this is my first post on this forum. My main problem is this: I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies

8. SCO

Network interfaces problem

Hi, I have problems with my SCO unix network interfaces. Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot. Installed driver using SCO Software manager - successfully Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies

9. IP Networking

Network interfaces problem

Hi, I have problems with my SCO unix network interfaces. Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot. Installed driver using SCO Software manager - successfully Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies

10. Solaris

HOW-TO Retrieve all network interfaces??!

Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies

Featured Tech Videos