Building a 43p using BOOTP


Login or Register for Dates, Times and to Reply

 
Thread Tools Search this Thread
Operating Systems AIX Building a 43p using BOOTP
# 1  
Building a 43p using BOOTP

I have a 43p 120 (7248-120) which I am trying to install AIX 5.2 on. I have built a Nimol server on a Linux PC running SUSE LES 10. I have setup the 43p to perfom a network boot (BOOTP) and all the addresses in the network settings under SMS are set to 0.0.0.0. When I power up the 43p it immediately finds the Nimol TFTP boot area and traffic starts to flow between the two machines.

However the 43p never actaully starts to build an operating system and the output from the DHCP log is as follows:

Jul 16 15:24:33 rs6000 dhcpd: BOOTREQUEST from 00:06:29:84:2b:36 via eth0
Jul 16 15:24:33 rs6000 dhcpd: BOOTREPLY for 192.168.0.5 to alter (00:06:29:84:2b:36) via eth0

It never gets any further!

Anyone any ideas?

I have not upgraded the firmware on the network adapter.
# 2  
I have not net installed AIX, but I have net install IRIX and Solaris.

Both basically do the following

IRIX loads a miniroot (about 20Meg) and that runs the whole installer.

Solaris loads a kernel but then has to mount root via NFS.

How are you expecting AIX to find the root file system for the installation?

Have you set up an NFS share for this purpose and, say, setup /etc/bootparams and started rpc.bootparamd?
# 3  
I have not checked the bootparams as the NIMOL system should take care of all the necessary NFS stuff. However NFS will not activate as the 43p has not accepted the BOOTP answer and the network adapter has not been allocated an address, that is the problem.
# 4  
Do you have rarpd running and the MAC address to IP mapping in /etc/ethers?

Are you expecting it to use RARP, BOOTP or DHCP to find it's IP address?
# 5  
Can I assume you mean on the SUSE Linux server?
# 6  
The Linux server is setup as a DHCP server and the AIX machine is defined in the DHCPD.CONF file with correct MAC address and the designated IP address. So I am expecting the clinet to have its IP address allocated by the DHCP system on the Linux server. By what is written in the DHCP logs the request is being answered but the client is not adopting the address.
# 7  
Sorry, but: failed at requirements.

a 43p-120 is a POWER3 machine (PPC604e) and hence only AIX-versions up to 5.1 are supported. As 5.1 is already out of service (and 5.2 will be in near future) you either get another machine (have a look at the IntelliStation POWER 185, for instance) or install 5.1 and live with the fact that you won't get any fix for it.

bakunin
Login or Register for Dates, Times and to Reply

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

Test Your Knowledge in Computers #281
Difficulty: Easy
A hypervisor or virtual machine monitor (VMM) is a computer software, firmware or hardware that creates and runs virtual private networks.
True or False?

10 More Discussions You Might Find Interesting

1. Solaris

Bootp/tftp issue neeeeeed help plz

i find a solution (2 Replies)
Discussion started by: shady_2005
2 Replies

2. AIX

EXP400 with 43P machine not booting

Hello I connected the exp400 & turned on the aix machine which is 7043-150 but now I guess probably ODM is corrupted as it does not boot. Its stuck at 0518 code. Also, on the console it shows stuck on the kernel, which then it does not want to boot. Is it possible to fix from maintenance... (1 Reply)
Discussion started by: pdhawan
1 Replies

3. AIX

brisque impose 43P 150 aix version 4 HELP!!!!!!!!

hi to everybody I have a problem with the AIX version 4: I can not get into failsafe session kindly someone knows how to enter this mode? thanks in advance (5 Replies)
Discussion started by: elektrospeed
5 Replies

4. AIX

model 43P 7248 Recovery!

HI all! this is my problem: my boss got a Model 43P 7248-100 PowerPC server with the AIX 4.2 os, but some days ago it crashed and now it doesn't want to boot up again, it stops after the initial diagnostic phase with the "PowerPC" screen! I must recover some important data from the hard disk, so... (6 Replies)
Discussion started by: AKO
6 Replies

5. SCO

Need help in BOOTP Server and Client configuration

Dear All; I need help in configuring the BOOTP server, I have found something on internet forums regarding the file: bootptab and editing some lines but Im not if they are all correct. Also, I need help to configure my clients (UNIX) to boot up with this bootp server(UNIX). I will be... (1 Reply)
Discussion started by: amirzandi
1 Replies

6. AIX

43p 120

I have acquired a 43p 120 (7248-120) and I have two questions: Can anyone remember what is the highest version of AIX which I can install (5.1 I believe) and Can anyone remember how to boot this from the CDROM (boot floppy?) (1 Reply)
Discussion started by: johnf
1 Replies

7. Linux

BOOTP on HP Thin clients

Please m new around here! Can anyone take me thru implementing bootp on my thin clients via my central server? Preciate ur assistance. Thanks folks! (2 Replies)
Discussion started by: chuk_uka
2 Replies

8. UNIX for Dummies Questions & Answers

Save 43p bios?

Is there any way to backup the bios on a 43P-140 7043? (0 Replies)
Discussion started by: freestyle10269
0 Replies

9. UNIX for Dummies Questions & Answers

Network Install PXE/BootP/TFTP

Im trying to help my professor at school, were trying to setup a linux server, that is configured with bootp/tftp/PXE. the client computer NICs have support to boot off PXE. What we would like to do is if a client computer does not have an OS, it would boot off the server, and display a menu to the... (1 Reply)
Discussion started by: kwalick
1 Replies

10. UNIX for Dummies Questions & Answers

bootp/tftp

Hi, Setting up print queue, using SMIT on AIX And I have an option saying do I wish to make this a BOOTP/TFTP server. What exactly does this do? Thanks (3 Replies)
Discussion started by: maverick
3 Replies

Featured Tech Videos