10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have Linux box with two interface cards.
Every card has it's own IP Address and Gateway, IP addresses are from different subnets.
eth0 192.168.1.10/24 GW 192.168.1.1
eth1 192.168.2.10/24 GW 192.168.2.1
Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2. IP Networking
Host - Ubuntu 12.04 desktop 64bit
Virtualizer - Oracle VirtualBox
Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router
Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out.
I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS?
Sam (2 Replies)
Discussion started by: sam4919
I have to problems ;
First ; I need to setup two NICs for a Solaris 10 server. But I could not do that unless giving different names in /etc/hosts file. like :
Second ; After solving first problem I have to setup my... (3 Replies)
Discussion started by: shadowfaxxxx
5. UNIX for Dummies Questions & Answers
Is there a way to determine for sure how many NIC ports installed on my Linux box?
I tried to run "lspci" but not sure about the results, it's not clear.
Below are the results when i run both "ifconfig" & "lspci" on my Linux box i hope someone can help me finding the actual numbers of... (1 Reply)
Discussion started by: Katkota
6. UNIX for Dummies Questions & Answers
Help, I have a Ubuntu headless server that has 5 NICs in it. The eth0-4 interfaces keep moving from NIC to NIC on boot up. I am told that there is a file that I can edit that will allow me to stabilize this but I need some help in determining the exact file and format for that file. All help will... (0 Replies)
Discussion started by: poundjd
I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1
Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA. (2 Replies)
Discussion started by: wschmied
Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address?
I know ifconfig -a but that only shows the plumbed and used interfaces.
cc (2 Replies)
Discussion started by: bigapple100
9. IP Networking
FreeBSD 4.8, Apache 1.3.27 - two NICs, one with a real-world IP plugged into a switch outside the PIX firewall, the other with a private IP plugged into a switch inside the PIX firewall. Apache listens on both IPs. my domain is mydomain.org.
so in /etc/rc.conf i have something like this (these... (10 Replies)
Discussion started by: ednix
10. UNIX for Dummies Questions & Answers
I am training to be support on our solaris based network and was wondering why solaris seems to assign the same mac address to all NICs placed in the machine regardless of how many NICs are in there, when i do a ifconfig -a all nics have same MAC.
Presumably this is a feature and there is... (1 Reply)
Discussion started by: hcclnoodles