Visit The New, Modern Unix Linux Community


VIOS requirement for FC and ethernet


 
Thread Tools Search this Thread
Operating Systems AIX VIOS requirement for FC and ethernet
# 1  
VIOS requirement for FC and ethernet

Hello,

I have some unclear about how VIOS uses its resources.

Assume that VIOS lpar has only 1 physical FC, and we use that to connect to the Lun. Then we install VIOS for the lpar on that Lun.
So my question is, afterward, we can still use that physical FC for the virtual FC we create later?

This can be same mechanism with virtual ethernet?
I have 1 physical ethernet assigned to vios, and configure IP on that, everything is fine until I tried to map another virtual ethernet to it and got the issue below:

Code:
$ mkvdev -sea ent0 -vadapter ent2 -default ent2 -defaultid 2
Adapter ent0 has an interface configured over it, or it belongs to another SEA, VLAN or EtherChannel
Command did not complete.

All of these mean that we have to use another physical device (FC, ethernet) for virtual devices??

Please advise me. Very appreciated Smilie
# 2  
On the VIOS, don't allocate an IP address to the adapter
configure the SEA, then create virtual adapter on the vios and add the IP to the virtual adapter.
For the fibre, are you saying you are booting the VIOS from SAN? No internal disks on the frame that you could use instead?
How many client VMs are you going to serve with the VIOS - will you have another VIOS on the same frame for redundancy ?
# 3  
Hi Zmaus,

Thank for your suggestion. I remove the IP from physical adapter, create new virtual adapter with "shared ethernet adapter".

Run again the command:
Code:
mkvdev -sea ent0 -vadapter ent2 -default ent2 -defaultid 2

Then, on AIX lpar (vio client) create new virtual ethernet. Then use smitty tcpip to configure the IP.
I can end up pinging the aix lpar Smilie

Regarding your question, this frame is no longer used in prod, so I took it as my test machine with few lpar and 1 VIOS only.

I have internal disks(SAS). But I wonder, if I have only 1 physical FC connected with LUN, Could I reuse it also for another virtual FCs to connect to other Lun? or I need another physical FC to do that?
# 4  
you can connect your fibre adapter to as many VMs as you want - you just need to configure the amount of virtuals you will probably need in the profile of the vios and then you just map

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

Test Your Knowledge in Computers #792
Difficulty: Easy
In mathematics and digital electronics, a binary number is a number expressed in the base-2 numeral system or binary numeral system.
True or False?

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Script requirement

Please help in creating script for below requirement. I will be running 1 command and will get below entries in a text file say file44.txt ******************************* DFDL1005 06:30 00:05 ABFL2003 10/22 01:10 CFTL1256 10/24 00:10 10/25 09:20 PM ******************************** .... (3 Replies)
Discussion started by: Vinay_3308
3 Replies

2. Shell Programming and Scripting

UNIX - requirement

Hi All, I have a source file with data Name ~ Groups Muni~abc,was,USA_ax,123 Chaitanya~USA_12,was Balaji~123,xyz,was Ramu~123,xyz From the second column i want to extract only the groups that matches the pattern 'USA_%' or if the group = 'was', and ignore any other columns. ... (8 Replies)
Discussion started by: morbid_angel
8 Replies

3. AIX

AIX VIOS IVM Ethernet problem

Hi All, I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box. We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
Discussion started by: KevB
11 Replies

4. AIX

VIOS IP address - separate vlan for vios servers ?

Hello, Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2. What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies

5. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies

6. Shell Programming and Scripting

URGENT REQUIREMENT

1.Write an automated shell program(s) that can create, monitor the log files and report the issues for matching pattern. (i) Conditions for creating log files. Log file is created with date (example 2010_03_27.log). If the log file size is 10 Mb for a particular day then automatically the log... (3 Replies)
Discussion started by: praveen12
3 Replies

7. Shell Programming and Scripting

Requirement

I am trying to script and came up with a conclusion that I need a do while loop in my statement. I am stuck with the do while syntax. I need to use it alongwith the if then else statement. Can I use it is a big question? I actually need to get all the files that are there from within run_dt to... (1 Reply)
Discussion started by: aronmelon
1 Replies

8. AIX

SPOT requirement

Hey May be a dumb question Can I use a SPOT which is at 5.3 TL6 to boot an LPAR (with 5.3 TL8) in to maintenance mode? Will it work ? Is it mandatory that SPOT should be of same or higher version in such case? Bala (1 Reply)
Discussion started by: balaji_prk
1 Replies

Featured Tech Videos