Have 1 question, assuming 1 FC has 2 ports (port 1 & 2). I create 2 virtual FC cards on lpart. And map both virtual FCs to the same physical FC. So what will happen? They use the same port 1 or port 2 or first virtual FC uses port 1 and second virtual FC use port 2?
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Hi
I had power issue that affected a server, in which I had power ON the server SPARC T1-B3 running solaris 10.
After power on the system stops at ok prompt, them I issued the following commands:
{0} ok setenv auto-boot? false
auto-boot? = false
{0} ok reset-all
SPARC T3-1B,... (10 Replies)
Hello,
Just a quick question
Usually from a PSERIES if you want to connect to IBM SAN Storage
you connect the IBM SAN Storage through a SAN Switch
something like this
---
however my question
Can you connect
from Pseries directly to San Storage without SAN Switch
what would be... (8 Replies)
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
hi
i have two aix servers and I was asked to setup a secure shell between the two servers using the sybase user. Can any one let me know how to do this (2 Replies)
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Hello,
I have two systems that are being prepared to be SAN attached ..
can anyone tell me any specific checks I should perform prior to the cards being installed...
I am aware of firmware / OS level and relevant drivers, is there anything else?
thanks
Chris. (8 Replies)
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
hpfc(7D) Devices hpfc(7D)NAME
hpfc - Agilent fibre channel host bus adapter
SYNOPSIS
PCI pci103c
DESCRIPTION
The hpfc fibre channel host bus adapter is a SCSA compliant nexus driver that supports all Agilent fibre channel host bus adapters, includ-
ing the HHBA5100x, HHBA5101x, and HHBA5121x models. Agilent host bus adapters support the fibre channel protocol on private fibre channel
arbitrated loops and fabrics. The driver supports up to ten host bus adapters, with a maximum of 125 fibre channel devices on each host bus
adapter. The hpfc driver supports a maximum of 256 LUNs per target.
The hpfc driver does not support the BIOS Int 13 feature, which enables the booting of an operating system. As a result, you should not
install an operating system on devices attached to the hpfc driver.
CONFIGURATION
The hpfc driver attempts to configure itself using the information in the /kernel/drv/hpfc.conf configuration file.
By default, the driver supports only LUN 0 for each target device. To add multiple LUN support, modify the /kernel/drv/sd.conf file.
Before upgrading the hpfc driver, backup the sd.conf file to save customized LUN settings and then use pkgrm(1M) to remove the old version
of the driver.
The host bus adapter port is initialized to FL_Port when connected to a fabric switch. To change it to F_Port, add the init_as_nport=1
entry to the hpfc.conf file and reboot the system.
To conserve system resources, at least one disk drive must be attached to the hpfc driver. If no devices are attached, the driver will not
load.
FILES
/kernel/drv/hpfc 32-bit ELF kernel module
/kernel/drv/sparcv9/hpfc 64-bit ELF kernel module
/kernel/drv/hpfc.conf Driver configuration file
/kernel/drv/sd.conf SCSI disk configuration file
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86, SPARC |
+-----------------------------+-----------------------------+
SEE ALSO luxadm(1M), pkgrm(1M), prtconf(1M), driver.conf(4), attributes(5), ses(7D), ssd(7D)
ANSI X3.272-1996, Fibre Channel Arbitrated Loop (FC-AL),
ANSI X3.269-1996, Fibre Channel Protocol for SCSI (FCP),
ANSI X3.270-1996, SCSI-3 Architecture Model (SAM),
Fibre Channel Private Loop SCSI Direct Attach (FC-PLDA)
SunOS 5.10 10 Oct 2000 hpfc(7D)