Unable to connect ASMI


Login or Register to Reply

 
Thread Tools Search this Thread
# 1  
Unable to connect ASMI

After following the instructions given by resident moderator Bakunin over here
Installed Memory 32GB but shows only 16GB

#1 Connect to ASMI
#2 Configure the deconfigured memory
#3 Start the machine

OK, everything is fine, however now cannot connect to ASMI through browser,
using both HMC Ports
Default IP 1 = 192.168.2.147
Default IP 2 = 192.168.3.147

able to ping both IPs, did a reset of service processor from the control panel 9113-550 , pulled the power plug and started, still same problem
1- able to ping both service IPs
2- but unable to use any browser to connect it

I couldn't find this on the board
Figure 6. Top view of the system (including service processor reset switch)
https://www.ibm.com/support/knowledg...5/iphah704.gif
IBM Knowledge Center Error




Code:
$ lssysconn -r all
resource_type=0,type_model_serial_num=9113-550*107780E,sp=unavailable,side=unavailable,ipaddr=192.168.2.147,alt_ipaddr=192.168.3.147,state=No Connection,eth_loc_code=U787B.001.DNW3313-P1-T5,alt_eth_loc_code=U787B.001.DNW3313-P1-T6
$

# lscfg | grep ibmvmc0
* ibmvmc0          U9113.550.107780E-V1-C2                                      Virtual Management Channel
#

# lsrsrc -a IBM.MCP
2610-431 Cannot enumerate resources for this command on node 10.1.1.124. The node is not currently in the cluster.
2610-431 Cannot enumerate resources for this command on node 10.1.1.129. The node is not currently in the cluster.
2610-429 The specified resource class is not installed on node 10.1.1.120.
Resource Persistent Attributes for IBM.MCP
resource 1:
        MNName           = "10.1.1.125"
        NodeID           = 1439001851767854463
        KeyToken         = "10.1.1.110"
        IPAddresses      = {"10.1.1.110"}
        ActivePeerDomain = ""
        NodeNameList     = {"10.1.1.125"}
# lsrsrc -a IBM.DRM
Resource Persistent Attributes for IBM.DRM


Can I reset ASMI from control panel codes or any other procedure ?

Last edited by filosophizer; 09-22-2018 at 03:16 PM..
# 2  
Quote:
Originally Posted by filosophizer
OK, everything is fine, however now cannot connect to ASMI through browser,
using both HMC Ports
Default IP 1 = 192.168.2.147
Default IP 2 = 192.168.3.147
I haven't used an IBM p-Series without a HMC for such a long time that i am not sure i can help you off the top of my head here. However, there might be all sorts of problems putting obstacles into the IP-communication between your browser and the Serviceprocessor.

First off, it might be that the IP addresses have once been changed and i am not sure if a simple SP-reset really changes that back to the defaults. (That i am not sure means just that: i don't know. If you have information in the affirmative, then perhaps it is so.)

Second, there is a sure-fire way to connect to the SP, whatever its IP might be: go to the data centre, connect a crossed-out cable to the SP connector 1 or 2 and connect your system directly to it. I have a small netbook for these purposes with a Wireshark/Ethereal software installed, so i can identify even unknown or fogotten IP-adresses. Once you identified the IP-address you still need the ASMI password, which is, btw., completely separate!

I hope this helps.

bakunin
# 3  
@Bakunin, thanks,

but I am able to ping from my laptop/pc to the service IP address which is
Default IP 1 = 192.168.2.147
Default IP 2 = 192.168.3.147

and also going to IVM, I can get the IP address for ASMI
Code:
$ lssysconn -r all
resource_type=0,type_model_serial_num=9113-550*107780E,sp=unavailable,side=unavailable,ipaddr=192.168.2.147,alt_ipaddr=192.168.3.147,state=No Connection,eth_loc_code=U787B.001.DNW3313-P1-T5,alt_eth_loc_code=U787B.001.DNW3313-P1-T6
$

The problem is
#1 I cannot connect to the IP address through any browser or any PC/laptop
# 4  
Quote:
Originally Posted by filosophizer
but I am able to ping from my laptop/pc to the service IP address which is
Default IP 1 = 192.168.2.147
Default IP 2 = 192.168.3.147
Yes, the IPs are active. Who tells you for sure that they are the service processors? They could be all sorts of systems, yes?

Quote:
Originally Posted by filosophizer
and also going to IVM, I can get the IP address for ASMI
Code:
$ lssysconn -r all
resource_type=0,type_model_serial_num=9113-550*107780E,sp=unavailable,side=unavailable,ipaddr=192.168.2.147,alt_ipaddr=192.168.3.147,state=No Connection,eth_loc_code=U787B.001.DNW3313-P1-T5,alt_eth_loc_code=U787B.001.DNW3313-P1-T6
$

OK, you have highlighted something, let me highlight something for you in return ;-)

Code:
$ lssysconn -r all
resource_type=0,type_model_serial_num=9113-550*107780E,sp=unavailable,side=unavailable,ipaddr=192.168.2.147,alt_ipaddr=192.168.3.14],state=No Connection,eth_loc_code=U787B.001.DNW3313-P1-T5,alt_eth_loc_code=U787B.001.DNW3313-P1-T6
$

I'd say the IVM awaits the interface to be where you are trying to find them. But it is not any more successful in that venture than you are. Therefore, eliminate all possible problems and connect directly to the system with a cross-over cable as suggested. That is a sure-fire method and if this fails the box is a case for the technician.

I hope this helps.

bakunin
This User Gave Thanks to bakunin For This Post:
# 5  
Quote:
Originally Posted by bakunin

I'd say the IVM awaits the interface to be where you are trying to find them. But it is not any more successful in that venture than you are. Therefore, eliminate all possible problems and connect directly to the system with a cross-over cable as suggested. That is a sure-fire method and if this fails the box is a case for the technician.

I hope this helps.

bakunin
Thanks, I have to try two things:
1- Reset Toggle which is on the board (not tried yet)

2- Cross Cable : May be that will work (just informing you, it was working with straight cable, then i reconfigured the deconfigured memory and then stopped connecting to ASMI via browser)
# 6  
Quote:
Originally Posted by filosophizer
2- Cross Cable : May be that will work (just informing you, it was working with straight cable,
I should have paid more attention to the model number: older models needed a crossover cable, newer ones don't (or, more correctly: don't care - they work with both). As it worked with a normal cable the first time your hardware is obviously new enough to ve able to use both, so the cable is not the problem.

I hope this helps.

bakunin
Login or Register to Reply

|
Thread Tools Search this Thread
Search this Thread:
Advanced Search

More UNIX and Linux Forum Topics You Might Find Helpful
Unable to connect using ftp
fretagi
hi I am having issues when trying to connect using ftp, I am having the following error: User (10.100.48.73:(none)): moz 331 Password required for moza. Password: 530 Login incorrect. Login failed. ftp> by 221 Goodbye. I have created a user like this: useradd -g 10 -d /lam/moza -m -s...... Solaris
11
Solaris
Unable to connect Wireless
cooltoad
I have managed to install Broadcom BCM43228 Wireless adapter on a laptop running CentOS 5.9 using instructions at: wiki.centos.org/HowTos/Laptops/Wireless/Broadcom I had the problem "Error for wireless request "Set Encode" (8B2A): SET failed on device... mentioned on the same page and solved...... Red Hat
0
Red Hat
Unable to connect SSH from HP-UX
ysafi
Hi, I'm trying to connect from an HP-UX with SSH2 client(ssh2 3.1.2 on hppa1.1-hp-hpux11.00) to an SSH2 server on a VxWorks system. The SSH connection is failing with the below connection logs: > /usr/local/bin/ssh2 -v -l testuser 10.10.10.10 debug: Ssh2/ssh2.c:1391: Using file...... HP-UX
4
HP-UX
Asmi errors
senmak
Hi friends How to clear the asmi deconfiguration errors.recently on cpu got deconfigured ibm assist to clear the error and to update the firmware please help me raj... AIX
0
AIX
Unable to connect to HP-UX 11.11 via eXceed 7.1
smokie
Hello HP-UX Gurus, I am having issues trying to start an x-session via eXceed 7.1. When I bring up eXceed via XDMCP Braodcast I see the host name and IP Address but when I try to connect the X window does not come up. I made the modification to the following file “/etc/dt/config/Xaccess”...... HP-UX
2
HP-UX