PowerVM SEA etherchannel performance ?


 
Thread Tools Search this Thread
Operating Systems AIX PowerVM SEA etherchannel performance ?
# 1  
Old 06-08-2018
PowerVM SEA etherchannel performance ?

Hello,

POWER7 machine.
4 x 1Gbit port ethernet adapter is dedicated to vios. 8023ad etherchannel is created using those 4 ports. Etherchannel adapter is shared to lpars using SEA.
If I test network performance directly from vios partition (using iperf) I'm geting nice 4Gbit throughput. But if I test from lpar partition (using iperf) I'm getting only about 1.5Gbit throughput (one time I saw 2Gbit, but never above 2Gbit).

Seems like SEA problem but where ?

Thanks,
Vilius M.
# 2  
Old 06-08-2018
largesend/large_receive?
This User Gave Thanks to agent.kgb For This Post:
# 3  
Old 06-09-2018
largesend=1 is default on my vios version - tried large_receive=yes - no change same result 1.4-1.8Gbit speed.
# 4  
Old 06-11-2018
It was largesend but nothing to do with vios or SEA, setting
Code:
# chdev -a mtu_bypass=on -l en0
# ifconfig -a
en0: flags=1e084863,14c0<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST,GROUPRT,64BIT,CHECKSUM_OFFLOAD(ACTIVE),LARGESEND,CHAIN>

on lpar network interface solves the problem - now I'm getting full 4Gbit speed.

Thanks,
Vilius M.
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. AIX

Powervm ivm vios

Hello, After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 ) i get this message "I/O hosting requires a hosting partition - boot not permitted". HMC was connected to the machine then HMC was removed through ASMI Searching on... (2 Replies)
Discussion started by: filosophizer
2 Replies

2. AIX

PowerVM/lpar creation problems

Hi, I'm a newbie to PowerVM and LPARs ( I work with VmWare and Oracle VM Server for Sparc) .recently we purchased an 8202-e4b server, with two enclosures for add'l disk capacity. it is licensed for PowerVM standard,came preloaded as such, AIX 7.1. I've set up HMC v8.2, and run it through a VM on... (30 Replies)
Discussion started by: computron
30 Replies

3. AIX

Etherchannel failover testing

Hi Guys, I am trying to test an etherchannel failover and switchback. I did failover from primary to backup adapter, but now I am not able to switch it back to primary. phcxxxxx:/ > entstat -d ent4 | grep Active Active channel: backup adapter ... (1 Reply)
Discussion started by: snchaudhari2
1 Replies

4. AIX

Need IBM PowerVM

Hi all please give me a link for IBM PowerVM (4 Replies)
Discussion started by: babinlonston
4 Replies

5. AIX

PowerVM HA questions

hi guys, i need to develop following setup for a customer: high availability oracle database on aix7 and linux in 2 different LPAR using dual ps700 blande a ds3400 and HMC. the question is, it is possible to have automatic vioc failover(aix,linux) when for example 1 vios goes down? in... (6 Replies)
Discussion started by: gullio23
6 Replies

6. AIX

Aggregated Etherchannel

Hi, I have a AIX5.3 P6-520 with 8x1Gb Ethernet ports with possible connections to 2 CISCO 2960 switches. I can create 8023ad Etherchannels which work correctly with the switches (I have set up for LACP passive and a valid channels) But can create 2x 8023ad 4Gb Etherchannels with no backups.... (2 Replies)
Discussion started by: spitzie
2 Replies

7. AIX

EtherChannel interface ping pelicularity

I have few AIX servers in my data center, which have their EtherChannel configured to have a fat pipe (active/active) and a nagios server to monitor the server uptimes. Nagios server pings every server in the data center and we have pretty much every known unix flavor in this data center. When... (3 Replies)
Discussion started by: thenomad
3 Replies

8. AIX

Can EtherChannel be a redundancy config?

I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches. How to make this as a redundancy config? Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies

9. AIX

AIX / Etherchannel / VLANs

I have 1 AIX server, 4 dual ported fiber attached ethernet cards and 4 VLANS coming in. Is it possible to present those 8 ports as 1 IP address using etherchannel? Thanks. (5 Replies)
Discussion started by: jwholey
5 Replies

10. AIX

Problem with Etherchannel

I'm trying to configure Etherchannel on AIX 5.3 and I'm having some problems. I am aggregating both of the onboard NIC's (ent0 and ent1) into a new adapter ent2 for failover reasons obviously. At first I was experiencing a problem where about 50% of all my packets would be dropped. Then after... (4 Replies)
Discussion started by: acascianelli
4 Replies
Login or Register to Ask a Question