10 More Discussions You Might Find Interesting
1. AIX
:wall::wall::wall:
1. I have created an LPAR in the HMC.
2. I have allocated the storage from an Hitachi AMS2500 and assigned it to the host group.
3. I have zoned the LPAR and Storage on a Brocade 5100. (The zone sees the AMS)
Next I activated the LPAR in the HMC, SMS mode for the mksysb... (3 Replies)
Discussion started by: Dallasguy7
3 Replies
2. AIX
Hi All,
I've been trying to create a new LPAR for some days now but I can't get the VIO server to recognize the new LPAR. This is what I did:
On HMC create new LPAR
On HMC create new virtual scsi adapter for LPAR in VIO profile
On HMC add new virtual scsi adapter for LPAR with DLPAR... (6 Replies)
Discussion started by: petervg
6 Replies
3. AIX
Just a question which may seem dumb to some out there, but then again I am not a super technie so that's my excuse.
Is it possible to say provision a test AIX LPAR (has a 10gb boot lun and 20gb data) under a VIO which has connectivity to SAN Array A so it can see the disks provisioned to it,... (2 Replies)
Discussion started by: Johnny1314
2 Replies
4. AIX
I am wondering if there is a command I can run from **with-in** LPAR server (server01) to find out the hostname or IP address or other parameters for VIO server in charge of server01? (1 Reply)
Discussion started by: ms1232
1 Replies
5. AIX
Whenever I assign/unassign a CDROM ( RAID CTRL ) to Active LPAR from HMC, I have to reboot the LPAR.
How can I do it without rebooting the LPARS.
POWER6 with HMC
LPARS = AIX 6.1
Any info
developerWorks : AIX and UNIX : PowerVM Forum : Moving CD-ROM/DVD-ROM dynamically ...
But... (5 Replies)
Discussion started by: filosophizer
5 Replies
6. AIX
hello Folks,
my vio:
$ lsmap -all
SVSA Physloc Client Partition ID
--------------- -------------------------------------------- ------------------
vhost0 U9117.MMA.6534BE4-V2-C11 0x00000003
VTD ... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. AIX
Hi,
I want to know wheather partition size for installation of vio client can be specified on vio server
example
If I am installing vio server on blade with 2*300gb hard disk,after that I want to create 2 vio client (AIX Operating system) wheather I can specify hard disk size while... (1 Reply)
Discussion started by: manoj.solaris
1 Replies
8. AIX
We have a frame the uses 2 vios that assign disk storage to LPAR's. We have a LPAr with multiple disk and I want to know how do I tell which vio is serving the disk. For example the LPAr has hdisk 0, 1, 2, 3 all the same size. I want to know which vio is serving hdisk0, 1. (4 Replies)
Discussion started by: daveisme
4 Replies
9. UNIX for Dummies Questions & Answers
Can you have a Dynamic LPAR without VIO and if yes is there a benefit to having both? I am attempting to implement VIO and Resource pooling at my company and want to understand the limitations.
Also, I have been told the managing and allocation of the Logical Volumes is a time consuming task as... (0 Replies)
Discussion started by: bombers73
0 Replies
10. AIX
I have a standard template I deploy for each of my AIX servers. It's in a mksysb format which I pulled via the nim server after I originally set it up.
I'm trying to restore this mksysb over the wire to a remote system. The remote system is an lpar running under vio (no HMC attached). The disk... (1 Reply)
Discussion started by: scottsl
1 Replies