Login or Register to Ask a Question and Join Our Community


AIX

Service IP issue in HACMP, Working with only one node

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems AIX Service IP issue in HACMP, Working with only one node
# 1  
Old 07-01-2011
Service IP issue in HACMP, Working with only one node
Hi,

I have a running HACMP Cluster with two nodes. Its working in active/passive mode. (i.e Out of the two nodes in the cluster one will be active and the other one will be on standby. If first node fails the other takes over)

1. There is a Service IP associated with the cluster. Now the issue is when my primary node is active I cannot ping the Service IP. But when I make the secondary node as active the Service IP is pingable.

2. The Persistent IP of only one of the nodes is pingable that too when i make the secondary node as active

Strange I guess I am missing something

Regards, Smilie
# 2  
Old 07-02-2011
@aixromeo
I doubt that there is something lay down in your security configuration e.g ( firewall )
What about TELNETTing or SSHing from , to and within both nodes , and post here again
also check out this troubleshooting guide
Checking the TCP/IP Subsystem > from page 85 to Checking the Cluster Communications Daemon page 93
# 3  
Old 07-03-2011
Hi, Thanks for the reply.

Well I did something very non-unix professional stuff Smilie.. I deleted the cluster...

Verified the /etc/hosts again.. started all over again. and lo it works! Hope not to do such stuff again Smilie

NOTE: This machine has not gone into production the reason i deleted the cluster.

@ h@foorsa.biz Thanks for the trouble shooting guide. A wonderfull resource for HACMP Troubleshooting

Regards,
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. AIX

Crash dump and Panic message : RSCT Dead Man Switch Timeout for HACMP; halting non-responsive node

Dear all i have two aix system -Model : P770 -OS version: AIX 6.1 -patch level : 6100-07-04-1216 -ha version : HACMP v 6.1.0.8 -host : A, B last Wednesday, my B system suddenly went down with crash dump. after 1 minute, A system went down with crash dump. I checked the dump of A-system... (6 Replies)
Discussion started by: tomato00
6 Replies

2. AIX

How to check if HACMP is running on AIX node?

Hello AIX experts, I have few queries and appreciate if you could help me with them. 1. How to check if HACMP (or any other AIX OS cluster) is installed 2. How to check if HACMP (or any other AIX OS cluster) is running 3. how to check which Oracle DB instance is running on it 4. how to... (1 Reply)
Discussion started by: prvnrk
1 Replies

3. AIX

HACMP two-node cluster with two SAN storages mirrored using LVM

HACMP two-node cluster with mirrored LVM. HACMP two-node cluster with two SAN storages mirrored using LVM. Configured 2 disk heartbeat networks - 1 per each SAN storage. While performing redundancy tests. Once one of SAN storage is down - cluster is going to ERROR state. What are the guidelines... (2 Replies)
Discussion started by: OdilPVC
2 Replies

4. AIX

HACMP with VIO, service IP failover

Would anyone please kindly help to solve this problem... An LPAR with the below network configuration. ent0 and ent1 are logical lan (virtual ethernet) from VIO SEA. en0 1.2.3.4 <- boot ip 192.168.1.1 <- persistent ip 192.168.1.10 <- service ip en1 11.22.33.44 <- boot ip When I... (6 Replies)
Discussion started by: skeyeung
6 Replies

5. AIX

Should GPFS be configured before/after configuring HACMP for 2 node Cluster?

Hi, I have a IBM Power series machine that has 2 VIOs and hosting 20 LPARS. I have two LPARs on which GPFS is configured (4-5 disks) Now these two LPARs need to be configured for HACMP (PowerHA) as well. What is recommended? Is it possible that HACMP can be done on this config or do i... (1 Reply)
Discussion started by: aixromeo
1 Replies

6. AIX

HACMP 5.4.1 Two-Node-Cluster-Configuration-Assistant fails

This post just as a follow-up for thread https://www.unix.com/aix/115548-hacmp-5-4-aix-5300-10-not-working.html: there was a bug in the clcomdES that would cause the Two-Node-Cluster-Configuration-Assistant to fail even with a correct TCP/IP adapter setup. That affected HACMP 5.4.1 in combinatin... (0 Replies)
Discussion started by: shockneck
0 Replies

7. AIX

Which files can be deleted in /usr in an aix hacmp node?

Hi Can ony one advise which files can be deleted in /usr in an aix hacmp node ? Im new to aix and Im not sure which files can be deleted ? #df -g /usr Filesystem GB blocks Free %Used Iused %Iused Mounted on /dev/hd2 7.00 1.00 86% 67013 22% /usr ... (4 Replies)
Discussion started by: samsungsamsung
4 Replies

8. AIX

hacmp in a 7 node configuration ?

Hi Guys, I have to design a multinode hacmp cluster and am not sure if the design I am thinking of makes any sense. I have to make an environment that currently resides on 5 nodes more resilient but I have the constrain of only having 4 frames. In addition the business doesnt want to pay for... (7 Replies)
Discussion started by: zxmaus
7 Replies

9. AIX

Node Switch Reasons in HACMP

Hi Guys, I have two nodes clustered. Each node is AIX 5.2 & they are clustered with HACMP 5.2. The mode of the cluster is Active/Passive which mean one node is the Active node & have all resource groups on it & the 2nd node is standby. Last Monday I noted that all resource groupes have been... (2 Replies)
Discussion started by: aldowsary
2 Replies

10. AIX

hacmp service ip

Hi, I have two resource grps in hacmp 5.2 cluster.One is cascading and other is concurrent. I have apply one svc_ip to cascading rg but not able to apply any svc ip with node bound option for concurrent rg. Can any one guide me with the step to apply svc ip . thanks in advance (0 Replies)
Discussion started by: aix_53
0 Replies
Login or Register to Ask a Question