10 More Discussions You Might Find Interesting
1. AIX
Hello,
After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 )
i get this message
"I/O hosting requires a hosting partition - boot not permitted".
HMC was connected to the machine
then HMC was removed through ASMI
Searching on... (2 Replies)
Discussion started by: filosophizer
2 Replies
2. AIX
Hi All,
I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM
Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box.
We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
Discussion started by: KevB
11 Replies
3. AIX
I am facing problems in moving CD-ROM from one lpar to another.
CDROM can be seen on the POWERVM (IVM) server , but through the web-access if I move it ( assign it ) to LPAR it will be assigned. I run cfgmgr , and the cdrom does not show up in the LPAR. I firmly believe this is the reason why I... (2 Replies)
Discussion started by: filosophizer
2 Replies
4. AIX
Hi,
When I try to login on my vios ivm website http://vios through the browser -- all three of them -- firefox , chrome , Internet Explorer , i get this error
http://vioserver/j_security_check
I have java installed on the machine from where i am trying to open up the IVM/VIOS webpage.
I... (2 Replies)
Discussion started by: filosophizer
2 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. AIX
Can somebody help me on IVM? I have installed vio 2.2 on a js21 server.
It has 2 physical ether ports, what I want to do is create ether channel say
en15 and en16 are physical and en17 is ether channel. I have created 2 clients on this server, now the question is can I map this en17 to both... (1 Reply)
Discussion started by: vjm
1 Replies
7. UNIX for Advanced & Expert Users
Solaris 10 Server refuse to connect :wall:
fork: Resource temporarily unavailable , server unexpectedly unavailable network connection , refuse error, disconnect message, fatal error type2, (protocol error type2)
Issue has been resolved after taken few steps :b:
First of all need to check... (1 Reply)
Discussion started by: taherahmed
1 Replies
8. AIX
Hi guys,
I am kind of new to this PowerVM thing.
I have created a virtual disk and partition.
With the IVM, when I try to open terminal wndow, a virtual terminal appeared and ask for password.
it says there:
In order to acess the terminal, you must first authenticate with IVM
Hostname... (2 Replies)
Discussion started by: wingcross
2 Replies
9. AIX
I have a bladecenter and js22, how to login IVM's command line such as HMC command line? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
10. AIX
I have a running VIO server that was managed via IVM. We made the (apparent) mistake of trying to connect a HMC server to it. Other than making a connection, no work has been done via HMC. We've since decided we don't want to use HMC and it's been powered off for a couple of weeks. However,... (1 Reply)
Discussion started by: cjs226
1 Replies