10-02-2001
ok I have an Ultra 5.
now here is the strange thing. I have run infconfig -a and yes hme0 does show up but no ip is assinged to it and it is not up. i have to manually ifconfig hme0 up to get that working. but then after that I don't know what to do. I tried to set up my gateway with route add default <address> this would be the gateway address I was assinged from my cable company. make any sense?
10 More Discussions You Might Find Interesting
1. IP Networking
I have managed to setup my Solaris box to receive an IP number from a DHCP server. In addition, I can ping and telnet between my dhcp server and my solaris box using the IP number. However, I can't resolve addresses by name from my solaris box.
In my nsswitch.conf file I have:
hosts: dns
... (4 Replies)
Discussion started by: marist89
4 Replies
2. Solaris
How is it possible to derive the very next IP that the solaris dhcp server is going to assign to the next host that requests? (0 Replies)
Discussion started by: ne0phyte
0 Replies
3. Solaris
Can any one tell me how to stop DHCP service on Solaris 10 so that it should not start nextime when the system is rebooted. (2 Replies)
Discussion started by: shabu
2 Replies
4. Solaris
I am trying to set up a DHCP on Sunblade 100. I have Dlink router that connects me to the net with my other computers. I can't seem to let my DHCP server to give out IP addresses instead of my router. I have been working on this for the last three days. I had an issue with Unknown name but i have... (4 Replies)
Discussion started by: aliban83
4 Replies
5. UNIX for Dummies Questions & Answers
I have a new solaris machine and I am trying to bring the same on network. The IP assignemnt is via DHCP. I want to know as which files need to be modified to include DHCP server IP in order that the machine gets its IP via DHCP server.
Thanks in Advance. :) (1 Reply)
Discussion started by: Ashvin Gaur
1 Replies
6. Solaris
Hello,
I need to configure a Cisco VLAN Accesspoint with DHCP using Solaris
dhtadm & pntadm
Network: 10.10.122.0 255.255.255.0
Default Router 10.10.122.1
Scope Range 10.10.122.10 - 254
Option 60 “Cisco AP c1142”
Option 43 ... (0 Replies)
Discussion started by: fredy82
0 Replies
7. Solaris
Dear All,
I have following configuration solaris 10 host
interface e1000g0 hold IP 10.124.73.178 having internet access natted to public ip on cisco switch
interface e1000g1 hold IP 192.168.8.10 DHCP server with DHCP client IP ranges 192.168.8.11 to 192.168.8.15
/etc/defaultrouter hold... (4 Replies)
Discussion started by: patel1678
4 Replies
8. Solaris
I need to find out the MAC address of an IP leased from DHCP server .
For Eg:-i need to know the MAC of the below mentioned IP at the below mentioned time .
IP : 172.16.28.90
Date :Sunday July 2nd 2011
Time : 14.07.2011
OS -Solaris 10
Vital QIP IP management software using to... (0 Replies)
Discussion started by: sandeep.tk
0 Replies
9. Solaris
Hi All,
Could you please let me know how can we check whether any given solaris machien is using DHCP or not.
is ps -ef | grep dhcp is full proof method or is their any other way. (10 Replies)
Discussion started by: omkar.jadhav
10 Replies
10. Solaris
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
LEARN ABOUT LINUX
if_mpadm
if_mpadm(1M) System Administration Commands if_mpadm(1M)
NAME
if_mpadm - change operational status of interfaces within a multipathing group
SYNOPSIS
/usr/sbin/if_mpadm -d interface_name
/usr/sbin/if_mpadm -r interface_name
DESCRIPTION
Use the if_mpadm utility to change the operational status of interfaces that are part of an IP multipathing group. If the interface is
operational, you can use if_mpadm -d to detach or off-line the interface. If the interface is off-lined, use if_mpadm -r to revert it to
its original state.
When a network interface is off-lined, all network access fails over to a different interface in the IP multipathing group. Any addresses
that do not failover are brought down. Network access includes unicast, broadcast, and multicast for IPv4 and unicast and multicast for
IPv6. Addresses marked with IFF_NOFAILOVER do not failover. They are marked down. After an interface is off-lined, the system will not use
the interface for any outbound or inbound traffic, and the interface can be safely removed from the system without any loss of network
access.
The if_mpadm utility can be applied only to interfaces that are part of an IP multipathing group.
OPTIONS
The if_mpadm utility supports the following options:
-d interface_name Detach or off-line the interface specified by interface_name.
-r interface_name Reattach or undo the previous detach or off-line operation on the interface specified by interface_name. Unless
the -d option was used to detach or off-line the interface, this option will fail.
EXAMPLES
Example 1: Detaching an Interface
Use the following command to off-line or detach the interface. All network access will failover from hme0 to other interfaces in the same
IP multipathing group. If no other interfaces are in the same group, the operation will fail.
example% if_mpadm -d hme0
Example 2: Reattaching an Off-line Interface
Use the following command to undo the previous operation. Network access will failback to hme0.
example% if_mpdadm -r hme0
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable |
+-----------------------------+-----------------------------+
SEE ALSO
ifconfig(1M), in.mpathd(1M), attributes(5)
DIAGNOSTICS
off-line failed as there is no other functional interface available in the multipathing group for failing over the network access.
This message means that other interfaces in the group are failed over already or the multipathing configuration was not suitable for com-
pleting a failover.
off-line cannot be undone because multipathing configuration is not consistent across all the interfaces in the group.
This message means that some interfaces in the IP multipathing group are not configured consistently with other interfaces in the group,
for example, one of the interfaces in the group does not have an IFF_NOFAILOVER address.
SunOS 5.10 3 Sep 2002 if_mpadm(1M)