09-18-2001
Unix Imaging for Redundancy
I'm trying to come up with an "imaging" type solution (a.k.a. Norton Ghost, Imagecast) with standard unix utils. I'd like to just image one of our FreeBSD servers so I can use the hot swap HD's. If one fails, I could slide in an exact duplicate HD and the server would be back up. I've tried just doing something with dd like: dd if=(hd1) of=(hd2) but it's not going to be that simple. I don't think dd is happy about not having a filesystem on hd2 (it's a blank unused drive). I have had luck with tarring up the whole drive, installing a minimal FreeBSD install on the second drive, renaming the kernel, dropping to single user mode, and then untarring, but that takes away the point of having something quick and ready to deploy.
I've also thought about running two mirrored drives (just like scsi+raid) but in an IDE system. Then having the secondary drive deactivated, but ready to go in case the first one fails. Then just tell the bios (through remote console interface) to boot from the slave drive. Thanks in advance for any ideas.
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Does anyone know of any good imaging tools that can be used to create an image of a Sco-Unix box? (2 Replies)
Discussion started by: gmrfh1
2 Replies
2. UNIX for Advanced & Expert Users
Dears,
I have server has two port's(Enet0,Enet1) what I want as follows:
Make the two port's has same IP address
where, if the port Enet0 became down automaticly Enet1 become up :confused: .
Amen (4 Replies)
Discussion started by: amen00
4 Replies
3. UNIX for Advanced & Expert Users
Here we want to implement the network redundancy on UNIX with the software.
The two network interface cards are configured on the UNIX node,once one card is down or unnormal,the other can take over. Those aplications that used the tcp ,udp,multicast protocol can also been switched at the same... (2 Replies)
Discussion started by: Frank2004
2 Replies
4. UNIX for Dummies Questions & Answers
We have had some email outages in the last few months and my boss is asking is it worth going with one of those email redundancy/filtering sites. The thing is, we have a backup server on a remote location, so I am pretty sure we can set something up with what we have already.
At the moment... (1 Reply)
Discussion started by: edzillion
1 Replies
5. Red Hat
Can anyone recommend an imaging solution for RedHat Linux that would allow base imaging with the ability to do incremental updates and encryption? I know Acronis has a version available, but it is rather pricey.
Thanks. (0 Replies)
Discussion started by: here2learn
0 Replies
6. Solaris
Hello,
Yes, it's me again. Running around getting this done! My current problem is I'm trying to image one drive 0 (/dev/dsk/c1t0d0s0) to drive 1 (/dev/dsk/c1t1d0s0). I know that drive1 came out of a Sun Server and it is a Sun drive. Solaris 10 recognized drive1 after the devfsadm command. The... (8 Replies)
Discussion started by: adelsin
8 Replies
7. AIX
Hi Guys,
I'm working on building a new 595 machine.. I'm try to achieve high availability for the VIO clients using 2 VIO servers, The ethernet part is satisfied using SEA failover, Now how do I achieve redundancy for the disks, its the servers internal disk attached to the scsi cards...
... (2 Replies)
Discussion started by: kkeng808
2 Replies
8. AIX
Have been learning a lot off late and am a little unclear about the VIOS setup particularly with regards to redundancy. Would appreciate your help.
My question is very basic. Lets say I have setup a VIOS and 3 LPARs on only one hdd (non scsi). On what do I setup the second VIOS? Could I for... (7 Replies)
Discussion started by: theaixeman
7 Replies
9. AIX
I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches.
How to make this as a redundancy config?
Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies