Sponsored Content
Full Discussion: About raw partition
Operating Systems Solaris About raw partition Post 46993 by RajaRC on Saturday 31st of January 2004 01:41:22 AM
Old 01-31-2004
Hi RTM,

Thanks a lot for the detailed information. It solved my problem.

Regards,
Raja
 

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

understanding logical partition, physical partition

hi, 1) is logical partition the same as physical partition except that one is physical and the other is logical? 2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies

2. Linux

Raw partition check

Hi I have Redhat linux 9. How can I check the size of a raw partition Regards, Raja Cool Linux!!! (2 Replies)
Discussion started by: RajaRC
2 Replies

3. UNIX for Dummies Questions & Answers

I've created a partition with GNU Parted, how do I mount the partition?

I've created a partition with GNU Parted, how do I mount the partition? The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards. Thanks, --Todd (1 Reply)
Discussion started by: jtp51
1 Replies

4. Solaris

Partition overlaps another partition while creating new parition in solaris

hi all while formatting hard disk i am getting following error. Partition 1 ends at 266338338 It must be between 34 and 143374704. label error: EFI Labels do not support overlapping partitions Partition 8 overlaps partition 1. Warning: error writing EFI. Label failed. I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies

5. AIX

AIX 5.3 using raw partition for Oracle 10g

Hellow friends, We are having AIX 5.3 total memory allotted to /Backup directory is 700GB actual used memory is 250GB ..but when i issue df -gt command to check space it is showing /Backup directory is 70% full ..how to identify root cause.? (1 Reply)
Discussion started by: umashankar1987
1 Replies

6. Red Hat

Is it possible to extend a extended partition raw space in harddisk thru rhel 6

hi all, As going thru LVM concepts in rhel 6, got hit with a question about "how to use the raw partition of an harddisk which extended volume is taken a bit" please find the attached diagram... is it possible to use this raw space with previously created extended partition without data... (13 Replies)
Discussion started by: redhatlbug
13 Replies

7. UNIX for Dummies Questions & Answers

Create a raw partition

Hi, I had created a primary partition (/dev/sda3) and made ext3 file system on it. then mounted it on a directory and touch a file (x) into this partition. however, I want to remove this partition and recreate it as an empty partition. so I used 'd' in fdisk command and delete that partition.... (3 Replies)
Discussion started by: Siavash sh
3 Replies

8. Red Hat

Shrink LVM partition & create new Linux Primary partition

Hello All, I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows, /boot - Linux Partition & another is LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc). Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.53 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 04:30 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy