Sponsored Content
Full Discussion: NIC driver building question
Top Forums UNIX for Dummies Questions & Answers NIC driver building question Post 4696 by Neo on Monday 30th of July 2001 10:58:00 AM
Old 07-30-2001
http://www.ibiblio.org/pub/Linux/docs/HOWTO/Hardware-HOWTO

Is your ethernet card supported?

Go here, for answers:

http://www.ibiblio.org/pub/Linux/doc...Hardware-HOWTO
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

NIC Driver

Hi:- I am trying to install a device driver for Intel NIC card on TurboLinux, but getting following errors, cc -O -Wall -o eepro100-diag eepro100-diag.c eepro100-diag.c:72: unistd.h: No such file or directory eepro100-diag.c:73: stdio.h: No such file or directory eepro100-diag.c:74:... (1 Reply)
Discussion started by: s_aamir
1 Replies

2. IP Networking

NIC driver guide

Hi I need to know how a driver for a network interface card works, I want to learn the basic principles since I know that every driver has its specific implementation. For example when we speak about the scheduler, we can read an operating system book and learn general design concepts e.g.... (0 Replies)
Discussion started by: Puntino
0 Replies

3. SCO

install NIC driver for Intel Pro 1000

hi I have a fresh installation of SCO 5.0.6 and I have download a NIC driver for Intel Pro 1000: ftp://ftp.sco.com/pub/openserver5/507/drivers/eeG_5.0.7g/VOL.000.000 Howto install it using floppy? ---------- Post updated at 04:02 PM ---------- Previous update was at 02:18 PM... (0 Replies)
Discussion started by: ccc
0 Replies

4. Red Hat

How to verify the current NIC driver version installed in RHEL5.3??

Guys, Can you help me how to verify the current installed NIC driver version in RHEL5.3? Thanks.:D (1 Reply)
Discussion started by: shtobias
1 Replies

5. UNIX for Advanced & Expert Users

How does a NIC driver activate with upper layer mutually?

Hi, all: How can I know whether the packets recieved from network by my own NIC driver are transmitted to upper layer(IP layer) or not? How can I know if the packets come from upper layer are passed to my own NIC driver and go out further? Is there any shell command or utility show... (9 Replies)
Discussion started by: liklstar
9 Replies

6. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

7. Solaris

Packaging driver for NIC

Hi guys My friend needs nfo driver for his Solaris box. I installed that driver for myself from scratch and he needs that driver in SVR4 format. I downloaded source code and run make and this is the point I don't how to proceed. How can I recognize which needs go to the package ? Does make... (0 Replies)
Discussion started by: solaris_user
0 Replies

8. UNIX for Advanced & Expert Users

My NIC driver couldn't send and recieve data simultaneously?

Hi, all: My writed NIC driver for rtl8139d adapter on linux 3.0.4 cannot send and recieve simultaneously but is able to send or recieve in parallel respectively. As soon as it send and recieve at the same time, the transmmition rate on both directions gradually decrease to zero b/s and report... (0 Replies)
Discussion started by: liklstar
0 Replies

9. Programming

My NIC driver cannot send and recieve in parallel!

Hi, all: My writed NIC driver for rtl8139d adapter on linux 3.0.4 cannot send and recieve simultaneously but is able to send or recieve in parallel respectively. As soon as it send and recieve at the same time, the transmmition rate on both directions gradually decrease to zero b/s and report... (1 Reply)
Discussion started by: liklstar
1 Replies

10. Solaris

Finding the NIC driver version on Solaris 11

In Solaris 10 it was easy, a simple grep through modinfo output and you'd have the version of any loaded module, including your NIC drivers. In my career I've seen many people relying on this information in their scripts. Now I'm on Solaris 11, and where have the version numbers gone? The... (0 Replies)
Discussion started by: cambridge
0 Replies
Ns_Url(3aolserver)					   AOLserver Library Procedures 					Ns_Url(3aolserver)

__________________________________________________________________________________________________________________________________________________

NAME
Ns_AbsoluteUrl, Ns_ParseUrl, Ns_RelativeUrl, Ns_SkipUrl - URL manipulation routines SYNOPSIS
#include "ns.h" int Ns_AbsoluteUrl(Ns_DString *pds, char *url, char *baseurl) int Ns_ParseUrl(char *url, char **pprotocol, char **phost, char **pport, char **ppath, char **ptail) char * Ns_RelativeUrl(char *url, char *location) char * Ns_SkipUrl(Ns_Request *request, int n) _________________________________________________________________ DESCRIPTION
Ns_AbsoluteUrl(pds, url, baseurl) Construct an URL based on baseurl but with as many parts of the incomplete url as possible. Return NS_OK or NS_ERROR. Ns_ParseUrl(url, pprotocol, phost, pport, ppath, ptail) Parse a URL into its component parts. Pointers to the protocol, host, port, path, and "tail" (last path element) will be set by ref- erence in the passed-in pointers. The passed-in url will be modified. Ns_RelativeUrl(url, location) If the url passed in is for this server, then the initial part of the URL is stripped off. e.g., on a server whose location is http://www.foo.com, Ns_RelativeUrl of "http://www.foo.com/hello" will return "/hello". Returns a pointer to the beginning of the relative url in the passed-in url, or NULL if error. Will set errno on error. Ns_SkipUrl(request, n) Return a pointer n elements into the request's url. SEE ALSO
nsd(1), info(n) KEYWORDS
AOLserver 4.0 Ns_Url(3aolserver)
All times are GMT -4. The time now is 08:02 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy