Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Quick Poll: Solaris IP Multipathing
Special Forums IP Networking Quick Poll: Solaris IP Multipathing Post 44400 by RTM on Friday 5th of December 2003 11:16:28 AM
Old 12-05-2003
Quote:
Whenever a single point of failure can be removed, it should be.
If it is cost effective. In the case of interface cards it is but then add in the cost of using two ports for each network your one system is on...more switches are needed, folks complain about running out of IP addresses...some battles are not worth it. If you had a SUN E10K, you would have to buy a second because of the single point of failure that is internal to it. Quite costly.
 

7 More Discussions You Might Find Interesting

1. Solaris

Quick question about Solaris =)

:D Just curious, I know that solaris 2.0-2.x_present are System V UNIX... But, I have only used Solaris 10, 9 and 2.5... On a 2.5 Sparc box, after you login you get presented with the usual SunOS 5.5.1 then UNIX(R) System V Release 4.0 I know Solaris 9 and 10 do not include this banner... ... (0 Replies)
Discussion started by: ssorel
0 Replies

2. Solaris

solaris multipathing

I have solaris 10 sparc. I installed a Qlogic hba card. This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay. I formated 2 luns. On my solaris system, i have 4 disk. How to configure solaris 10 to fix the dual disk view. ... (4 Replies)
Discussion started by: simquest
4 Replies

3. Solaris

Solaris IP Multipathing (IPMP) Help

Hello All, I work for a Health care company at a local trauma hospital. I maintain a Picture Archiving and Communication System (PAC's). Basically, any medical images (X-Ray, CT, MRI, Mammo, etc) are stored digitally on the servers for viewing and dictation from diagnostic stations. I took over... (10 Replies)
Discussion started by: mainegeek
10 Replies

4. Solaris

Solaris IP Multipathing

Hi, I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation . I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2. Now is it possible to have IP Multipathing on each of the servers as follows ? ... (0 Replies)
Discussion started by: maadhuu
0 Replies

5. Solaris

Disable Inbuilt multipathing software of Solaris 10

Dear UNIX Gurus I need to know how to disable MPXIO feature (Inbuilt multipathing software of Solaris 10) as we are going to implemented iSCSI EMC based SAN. I am bit new to this feature so kindly suggest how to disable it Regards (4 Replies)
Discussion started by: girish.batra
4 Replies

6. Solaris

Solaris multipathing

Hai we using emc storage which is conneted to M5000 through san switch. we asign 13 luns but in server it is showing 22 luns. i enable the solaris multipathing (MPxIO) #more /kernel/drv/fp.conf in that file MPxio-disable=no #mpathadm list lu it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies

7. Solaris

ZeusIOPS multipathing failed Solaris 11

hi, just installed solaris 11.1 (11.1.9.5.1) on a sun7410 ZFSSA (x4440 + j4400), but when I enable multipathing with "stmsboot -e", only the 1TB SATA drives inside the j4400 are configured as multipathed vhci / mpxio devices, but the logzillas / ZeusIOPS drives are skipped. the server is... (0 Replies)
Discussion started by: pressy
0 Replies
All times are GMT -4. The time now is 02:31 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy