Sponsored Content
Full Discussion: IPSec - VPN using shared key
Special Forums Cybersecurity IPSec - VPN using shared key Post 34240 by Neo on Tuesday 11th of February 2003 10:08:56 AM
Old 02-11-2003
Perhaps you would be better off using a simple shared secret between the two implementations. This shared secret would be used to establish a session key.

Did you try this to see if it would work? Did you establish a tunnel with only shared secrets (this is called a pre-shared key in the article below)?

http://www.onlamp.com/lpt/a/3043

Also, see the following article on setting up a BSD-LINUX IPSEC tunnel:

http://home.t-online.de/home/hburde/ipsec/node1.html
 

8 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

How to interpret the shared memory key

I'm facing a problem interpreting the shared memory key on an AIX machine. (1) I go to a property file and I see the following: shm_key = "119112066" (2) So I now go the command prompt and do this: ipcs -m | grep 119112066 And, I do not find it. So what I do is to run the... (2 Replies)
Discussion started by: vijaygade
2 Replies

2. IP Networking

IPSec VPN Routing

Hello, I'm trying to setup a gateway VPN between two routers across an unsecured network between two local networks. The routers are both linux and I'm using the ipsec tools, racoon and setkey. So far hosts from either local net can successfully ping hosts on the other local net without issue. ... (0 Replies)
Discussion started by: salukibob
0 Replies

3. Solaris

Solaris 8 ssh public key authentication issue - Server refused our key

Hi, I've used the following way to set ssh public key authentication and it is working fine on Solaris 10, RedHat Linux and SuSE Linux servers without any problem. But I got error 'Server refused our key' on Solaris 8 system. Solaris 8 uses SSH2 too. Why? Please help. Thanks. ... (1 Reply)
Discussion started by: aixlover
1 Replies

4. Cybersecurity

IPSEC

hello, after configuration ipsec in ip4 I can not ping between client and server whereas I had success ping before configuration! I also generate different key for AH and ESP as i have shown below. what is my problem and what should i do to have ping and test the configuration? code: ... (0 Replies)
Discussion started by: elinaz
0 Replies

5. Programming

Shared library with acces to shared memory.

Hello. I am new to this forum and I would like to ask for advice about low level POSIX programming. I have to implement a POSIX compliant C shared library. A file will have some variables and the shared library will have some functions which need those variables. There is one special... (5 Replies)
Discussion started by: iamjag
5 Replies

6. IP Networking

VPN IPSec Openswan

Hi all, I have installed Openswan and configured IPSec and works perfect, but for some unknown reasons it stop working. I see that the tunnels are up and established. The route to the destination are added. Everything by the book seems to be ok. But somehow when i start to ping the other side (... (4 Replies)
Discussion started by: ivancd
4 Replies

7. IP Networking

IPSec Openswan Site to Site VPN - Big Pain

Hi @all, I try to connect 2 LANs with IPSec/Openswan LAN 1: 192.168.0.0/24 LAN 2: 192.168.1.0/24 This is my Config: conn HomeVPN # # Left security gateway, subnet behind it, nexthop toward right. left=192.168.1.29 ... (1 Reply)
Discussion started by: bahnhasser83
1 Replies

8. IP Networking

Best tool to monitor VPN IPSEC Tunneling

We are using cyberoam device, VPN IPSEC tunnel is going of frequently even the traffic is throug. Please suggest what may be the cause for the above mentioned issue. Also suggest a best tool to monitor the same VPN IPSEC tunnel connectivity. (4 Replies)
Discussion started by: marunmeera
4 Replies
URI::URL(3pm)						User Contributed Perl Documentation					     URI::URL(3pm)

NAME
URI::URL - Uniform Resource Locators SYNOPSIS
$u1 = URI::URL->new($str, $base); $u2 = $u1->abs; DESCRIPTION
This module is provided for backwards compatibility with modules that depend on the interface provided by the "URI::URL" class that used to be distributed with the libwww-perl library. The following differences exist compared to the "URI" class interface: o The URI::URL module exports the url() function as an alternate constructor interface. o The constructor takes an optional $base argument. The "URI::URL" class is a subclass of "URI::WithBase". o The URI::URL->newlocal class method is the same as URI::file->new_abs. o URI::URL::strict(1) o $url->print_on method o $url->crack method o $url->full_path: same as ($uri->abs_path || "/") o $url->netloc: same as $uri->authority o $url->epath, $url->equery: same as $uri->path, $uri->query o $url->path and $url->query pass unescaped strings. o $url->path_components: same as $uri->path_segments (if you don't consider path segment parameters) o $url->params and $url->eparams methods o $url->base method. See URI::WithBase. o $url->abs and $url->rel have an optional $base argument. See URI::WithBase. o $url->frag: same as $uri->fragment o $url->keywords: same as $uri->query_keywords o $url->localpath and friends map to $uri->file. o $url->address and $url->encoded822addr: same as $uri->to for mailto URI o $url->groupart method for news URI o $url->article: same as $uri->message SEE ALSO
URI, URI::WithBase COPYRIGHT
Copyright 1998-2000 Gisle Aas. perl v5.14.2 2012-02-11 URI::URL(3pm)

Featured Tech Videos

All times are GMT -4. The time now is 07:44 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy