Hello.
I just installed a SCO Openserver 6 box and it's suckin' mud.
sar -v (see below) shows something that has me quite concerned... after time, it shows that the number of inodes being used as a negative value. When this happens, the server runs extremely slow until I reboot. The server... (0 Replies)
I am looking for advice on a router. I am new to Linux and am trying to use Limewire and Ktorent and can make no connection. Limewire indicates I have a firewall. I have a Linksys router WRK54G and my guess is that is the problem. I have spent hours upon hours trying to get it to work using info... (0 Replies)
Hello,
I have a list like this :
1
2
-4
0
-3
-7
5
6 etc.
Is there a way to remove all the positive values and print only the negative values, without using grep, sed or awk?
Thanks,
Prasanna (4 Replies)
Hi, i need help on replacing negative values in a column with 0. any quick fix on this? thanks much. for instance,
input:
1
2.3
-0.4
-25
12
13
45
-12
desired output
1
2.3
0
0
12
13
45 (4 Replies)
Hi,
I am trying to add a static route in one of 3 server (S3) so that I can access the main application server (S1). But problem is, the server (S3) where I am trying to add static route is connected with another server (S2) which is in same private network of application server (S1).
I have... (9 Replies)
Hi All,
i have 20 Obligors when ever i dont find all of them on particular row/line from each in put i need to print it in different file.
using below command but it is not working please help at earliest.
Steps:
set -A FILENAME $( cat... (10 Replies)
Can anyone please assist me?
Please find the attached input and output file for ur reference.
a)Incase if i get negative value (ex:-000100) in the 11th column then i have to convert the value to 0000000(7 zeros-length is 7) and then
print the entire record.
b)Incase if there is no... (2 Replies)
Hi Gurus,
I have requirement need to sum the value, the logic is if the value is negative then time -1, I tried below two ways. one is failed, another one doesn't work.
awk -F"," '{if($8< 0 $8*-1 else $8) sum+=$8}{print sum, $8} END{printf("%.2f\n",sum)}'
awk -F","... (4 Replies)
Discussion started by: ken6503
4 Replies
LEARN ABOUT NETBSD
arcmsr
ARCMSR(4) BSD Kernel Interfaces Manual ARCMSR(4)NAME
arcmsr -- Areca Technology Corporation SATA/SAS RAID controller
SYNOPSIS
arcmsr* at pci? dev ? function ?
DESCRIPTION
The arcmsr driver provides support for the PCI-X and PCI Express RAID controllers from Areca Technology Corporation:
- ARC-1110 PCI-X 4 Port SATA RAID Controller
- ARC-1110ML PCI-X 4 Port SATA RAID Controller
- ARC-1120 PCI-X 8 Port SATA RAID Controller
- ARC-1120ML PCI-X 8 Port SATA RAID Controller
- ARC-1130 PCI-X 12 Port SATA RAID Controller
- ARC-1130ML PCI-X 12 Port SATA RAID Controller
- ARC-1160 PCI-X 16 Port SATA RAID Controller
- ARC-1160ML PCI-X 16 Port SATA RAID Controller
- ARC-1170 PCI-X 24 Port SATA RAID Controller
- ARC-1200 Rev A PCI Express 2 Port SATA RAID Controller
- ARC-1202 PCI Express 2 Port SATA RAID Controller
- ARC-1210 PCI Express 4 Port SATA RAID Controller
- ARC-1220 PCI Express 8 Port SATA RAID Controller
- ARC-1230 PCI Express 12 Port SATA RAID Controller
- ARC-1230ML PCI Express 12 Port SATA RAID Controller
- ARC-1231ML PCI Express 12 Port SATA RAID Controller
- ARC-1260 PCI Express 16 Port SATA RAID Controller
- ARC-1260ML PCI Express 16 Port SATA RAID Controller
- ARC-1261ML PCI Express 16 Port SATA RAID Controller
- ARC-1280 PCI Express 24 Port SATA RAID Controller
- ARC-1280ML PCI Express 24 Port SATA RAID Controller
- ARC-1680 PCI Express 8 Port SAS RAID Controller
- ARC-1680LP PCI Express 8 Port SAS RAID Controller
- ARC-1680i PCI Express 8 Port SAS RAID Controller
- ARC-1680x PCI Express 8 Port SAS RAID Controller
- ARC-1681 PCI-X 8 Port SAS RAID Controller
These controllers support RAID levels 0, 1, 1E, 3, 5, 6, and JBOD using either SAS or SATA II drives.
arcmsr supports management and monitoring of the controller through the bioctl(8) and envstat(8) commands.
Please note, however, that to use some features that require special privileges, such as creating/removing hot-spares, pass-through disks or
RAID volumes will require to have the password disabled in the firmware; otherwise a Permission denied error will be reported by bioctl(8).
When a RAID 1 or 1+0 volume is created, either through the bioctl(8) command or controller's firmware, the volume won't be accessible until
the initialization is done. A way to get access to the sd(4) device that corresponds to that volume without rebooting, is to issue the fol-
lowing command (once the initialization is finished):
$ scsictl scsibus0 scan any any
The arcmsr driver will also report to the kernel log buffer any error that might appear when handling firmware commands, such as used by the
bioctl(8) command.
EVENTS
The arcmsr driver is able to send events to powerd(8) if a volume or any drive connected to the volume is not online. The state-changed
event will be sent to the /etc/powerd/scripts/sensor_drive script when such condition happens.
SEE ALSO intro(4), pci(4), scsi(4), sd(4), bioctl(8), envstat(8), powerd(8), scsictl(8)HISTORY
The arcmsr driver first appeared in NetBSD 5.0.
AUTHORS
The arcmsr driver was originally written for OpenBSD by David Gwynne. It was ported to NetBSD and extended by Juan Romero Pardines.
BSD March 3, 2008 BSD